5.
OPERATION
Note:
• Be sure
to
read this chapter referring
to
the front diagrams
of
chapter 2. CONTROLS on page 3 (unfold).
Basic Operation
"""::::::;,i;;nllillilllii
Wh;ri<fh;;~:~iti;t~;~;d~~:;t~;ti~~<~~d:;toP-
ping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
1)
Press the POWER button
[ID.
*
To
turn the power off, press the POWER button
for at least 1 second.
2)
Press the FUNC button
[ID
to select another
operation mode. The mode switches as fol-
lows each time the FUNC button
is
pressed:
Radio
~
Tape
~
CD changer
~
Radio
*If a component is not connected, that operation
mode cannot be selected.
*"CASS" appears when no tape is loaded
in
the
source unit, and "DISC" appears when no disc is
loaded
in
the CD changer.
Adjusting the volume
Turning the Rotary knob [I] clockwise increases
the volume; turning it counterclockwise decreas-
es the volume.
*The volume level is from a (minimum) to 33 (maxi-
mum).
Setting the Z-enhancer
This unit comes with 3 types of sound tone
effects stored
in
memory. Select the one you
prefer.
*The factory default setting is "OFF".
Each time you press Z-EHCR button
[zl
the tone
effect changes
in
the following order:
"Z-ENHANCER 1"
~
"Z-ENHANCER
2"
~
"Z-
ENHANCER
3"
~
"OFF"
~
"Z-ENHANCER
1"...
• Z-ENHANCER 1 : bass emphasized
• Z-ENHANCER 2 : treble emphasized
• Z-ENHANCER 3 : bass and treble empha-
sized
• OFF : no sound effect
6
XA311
Adjusting the tone
Press A-M button
[!]
and select the item to
adjust. Each time you press A-M button
[!], the
item changes
in
the following order:
"BASS"
~
"TREB"
~
"BAL"
~
"FAD"
~
Function mode
...
Adjusting the bass
1.
Press A-M button
[!]
and select "BASS".
2.
Turning the Rotary knob [I] clockwise
emphasizes the bass; turning it counter-
clockwise attenuates the bass.
*The factory default setting is "0". (Adjustment
range:
-6
to +6)
3.
When the adjustment
is
complete, press A-M
button
[!]
several times until the function
mode is reached.
Adjusting the treble
1.
Press A-M button
[!]
and select "TREB".
2.
Turning the Rotary knob [I] clockwise
emphasizes the treble; turning it counter-
clockwise attenuates the treble.
*The factory default setting is "0". (Adjustment
range:
-6
to +6)
3.
When the adjustment is complete, press A-M
button
[!]
several times until the function
mode is reached;
Adjusting the balance
1.
Press A-M button
[!]
and select "BAL".
2.
Turning the Rotary knob [I] clockwise
emphasizes the sound from the right speak-
er; turning
it
counterclockwise emphasizes
the sound from the left speaker.
*The factory default setting is "0". (Adjustment
range:
L9
to
R9)
3.
When the adjustment
is
complete, press A-M
button
[!]
several times until the function
mode
is
reached.
To Next Page
Loading...
Need help?
General
