Clarion XMA1 User Manual

5
XMA1
6. CASSETTE PRECAUTIONS AND CARE
7. OPERATION
Note:
• Be sure to read this chapter referring to the front diagrams of chapter 3. CONTROLS on page 3 (unfold).
When this unit is turned on, starting and stopping the engine of
a boat with its volume raised to the maximum level may harm
your hearing.
Be careful about adjusting the volume.
Basic Operations
1. Tape slack can lead to operating difficulties. Remove tape slack
before inserting a cassette, particularly when using C-90 or pre-
recorded cassettes.
2. Use C-30 to C-90 cassettes. Avoid use of
C-120 or longer cassettes (The very thin tape may stretch or break).
3. Clean the head periodically with a good commercial head cleaner.
Avoid touching the head with magnetic or hard objects.
4. Do not oil the cassette mechanism.
5. Always remove the cassette from the mechanism when not in
use. Exposure to direct sunlight, extreme temperatures or high
humidity may damage cassettes.
6. The cassette tape will automatically eject from the mechanism if it
is damaged. Always ensure that cassette tapes are in good con-
dition prior to use.
Adjusting the Treble
1) Press A-M button # and select “TREB”.
2) Press volume button 1 w to emphasizes the treble;
press z to attenuates the treble.
* The factory default setting is “0”. (Adjustment range: –6 to +6)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Adjusting the Balance
1) Press A-M button # and select “BAL”.
2) Press volume1 w to emphasizes the sound from the right
speaker;
press z to emphasizes the sound from the left speaker.
∗ The factory default setting is “0”. (Adjustment range: L9 to R9)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Adjusting the Fader
1) Press A-M button # and select “FAD”.
2) Press volume1 w to emphasizes the sound from the front
speaker;
press z to emphasizes the sound from the rear speakers.
∗ The factory default setting is “0”. (Adjustment range: F9 to R9)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Setting the Z-enhancer
This unit comes with three types of sound tone effects stored in
memory. Select the one you prefer.
∗ The factory default setting is “Z-EHCR OFF”.
Each time you press Z-EHCR button &, the tone effect changes in
the following order.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜ “Z-ENHANCER 3” ➜ “Z-
EHCR OFF” ➜ “Z-ENHANCER 1”...
• Z-ENHANCER 1: bass emphasized
• Z-ENHANCER 2: treble emphasized
• Z-ENHANCER 3: bass and treble emphasized
• Z-EHCR OFF: no sound effect
Loudness Function
Press the LOUD button # for at least 2 seconds to turn the loud-
ness function on and off.
Switching the Display
Press the DISP button % to enter the clock display mode.
Operation mode display ➜ Clock display ➜ Operation mode display
CAUTION
IMPORTANT
Door must be totally closed to prevent water go into the set!
OK NG
1) Press the POWER button 2.
∗ To turn the power off, press the POWER button for at least 1 second.
2) Press the FUNC button 2 to select the operation mode. The mode
switches as follows each time the FUNC button is pressed:
Radio ➜ Tape ➜ CD changer ➜ Radio
∗ If a component is not connected, that operation mode cannot be se-
lected.
∗ “CASS” appears when no tape is loaded in the source unit, and “DISC”
appears when no disc is loaded in the CD changer.
3) Use the volume button 1 to adjiust the volume.
w: Increases the volume.
z: Decreases the volume.
∗ The volume level is from 0 (minimum) to 33 (maximum).
Audio Mode Adjustments
Press the A-M button # to select the adjustment mode. The mode
switches as follows each time the A-M button is pressed:
BASS ➜ TREB ➜ BAL ➜ FAD ➜ Previous mode
Adjusting the Bass
1) Press A-M button # and select “BASS”.
2) Press volume button 1 w to emphasizes the bass;
press z to attenuates the bass.
∗ The factory default setting is “0”. (Adjustment range: –6 to +6)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.

Clarion XMA1 Specifications

General

Brand	Clarion
Model	XMA1
Category	Car Receiver
Language	English