CLAUSING 1300 Series - Drive Assembly

I
DRIVE ASSEMBLY
537-103
HUT.
1300 - 40
ADJUSTING
1400 - 108
^ 041 - 386
BRACKET, C ’ SHAFT
# ADDITIONAL PARTS NOT CONTAINED
r
IN THIS ASSEMBLY:
041 - 376 MOUNTING BRACKET (2)
041 - 386 C'SHAFT BRACKET
697-059
3/8 - 16 * 1 SOC HD CAP SCREW.
SPRING
3/8 - 16 * 1-1/4 HEX HD CAP SCREW (6)
932-091
CLUTCH ARM
\ 1/2 WASHER
1/2 - 13 * M/2 HEX HD CAP SCREW (2)
WASHER.
(2 REQ ’ D)
3/8 PLAIN WASHER (EXTRA THICK)
r
3/8 WASHER (EXTRA THICK) (7)
(EXTRA THICK)
(2 REQ ’ D)
1/2 WASHER (EXTRA THICK) (2)
3/8 - 16 HEX NUT (2)
390-029
HOSE.
VARISPEED
♦ 3/8 PLAIN
002-060
/
ARM. CLUTCH
\
WASHER
^1/2-13 x 1-1/2
(2 REQ ’ D)
r
(EXTRA THICK)
HEX. HD. CAP SCREW
(2 REQ ’ D)
^3 '8- 16 x 1-1.4
SOC. HD. CAP
5CREW
1/4 x 3/4
ROLL PIN
(2 REO D)
3/8 - 16 x 1
RETAINER,
P
SOC. HD. CAP
SCREW
;i
(UNC -3A
(4 REQ ’ D)
699- 160
SPACER
3
641-106
RETAINER.
064-011
RETAINERS)
P
BEARING,
BALL
641-122
RETAINER,
BOWED
BEARING.
296-048
FITTING,
45* ELBOW
641-129
RETAINER.
I
RING
1 4-20 x
SOC HD. CA
SCREW
(2 REQ ’ D)
131-014
CYLINDER.
i
UPPER
567-065
PACKING. ’ ’ 0 ” RING
/ (2 REQ ’ D)
1 (SPECIAL)
1 4-20
HEX. NUT
1/4-20x2-1/4
HEADLESS SET
SCREW
(OVAL PT.)
PLATE, CYLINDER
RETAINER
131-013
’ CYLINDER,
LOWER
567-059
PACKING
(2 REQ ’ D)
SOC.SET SCREW
RETAINER, RING
0^
\
SPACER,
(SELF LOCK, CUP PT.)
386-098
RUBBER
(2 REQ ’ D)
HOUSING. RIGHT
3/8-16 x
064-009 (ALUMINUM)
HEX. HD CAP SCREW
(4 REO ’ D)
BEARING, BALL
1400-111
CLUTCH SHIFTER
ASSEMBLY
3/8-16 x 1-1/4
S. SPINDLE ASSEMBLY
442-067
SOC HD. CAP
KEY,MOTOR
SCREW
(2 REQ ’ D)
PULLEY
HEX. HD. CAP SCREW
(2 REQ ’ D)
IMPORTANT
THE PARTS ILLUSTRATED ON
THIS PAGE ARE FOR LATHES
041 - 376
SERIAL NUMBERS FROM
BRACKET, MOUNTING
(SELF LOCKING)
(2 REQ ’ D)
131120 436'- 035 230/460 V 5 H.P
486 - 036 200 V 5 H.P.
486 - 047 (575V)
TO.
(4 REQ ’ D)
♦ 3/8 -16 HEX
NUT
(2 REQ ’ D) 698- 121
STUD, MOTOR
;
MOUNTING
(4 REO ’ D)
3/8 HEX
NUT
(4 REQ ’ D)
1300
I
3