Clear-Com TEMPEST 2400

Other manuals for Clear-Com TEMPEST 2400

Reference Manual108 pages

Quick Start Guide4 pages

Questions and Answers

E
Evan AllenSep 12, 2025
Why Clear-Com TEMPEST 2400 Intercom System BeltStation will not pair with BaseStation?
- C
  collinsjosephSep 12, 2025
  If your Clear-Com Intercom System BeltStation won't pair with the BaseStation, ensure the BaseStation is powered ON and in Operational Mode, and the BeltStation is powered OFF. Connect the pairing cable, then turn the BeltStation ON. A "Pairing Complete" message should appear. If it fails, try pairing a different BeltStation or substitute a new pairing cable. You can also try restoring memory settings to Factory Defaults or clearing the memory completely. As a last resort, reset the BaseStation memory to "Factory Defaults" or clear its memory.
S
Samantha GarnerAug 22, 2025
What to do if Clear-Com Intercom System BeltStation will not pair with BaseStation?
- L
  Larry RobertsAug 22, 2025
  If your Clear-Com Intercom System's BeltStation won't pair with the BaseStation, first ensure the BaseStation is powered ON and in Operational Mode. Connect the pairing cable from the BaseStation to the BeltStation and turn the BeltStation power ON. If it still fails, try pairing a different BeltStation or substitute a new pairing cable. As a last resort, restore memory settings to Factory Defaults, or clear the memory completely, and reset the BaseStation memory.
E
Edwin RussellAug 25, 2025
What to do if Clear-Com TEMPEST 2400 Intercom System BeltStation will not log into BaseStation?
- C
  chandlerjonathanAug 25, 2025
  If a BeltStation from your Clear-Com Intercom System won't log into the BaseStation, check these things: 1. Make sure the BeltStation is powered ON and has sufficient battery charge. 2. Verify the correct BaseStation is selected on the BeltStation’s “Select Base” menu. 3. Ensure there is an available slot on the BaseStation. 4. Check the Static and Dynamic slot display settings on the BaseStation. 5. Determine if any other BeltStation is logged onto the BaseStation. If none of these steps work, try re-pairing the BeltStation to the BaseStation or attempt to log into another BaseStation, if available. As a final option, follow the memory reset procedure under Factory Defaults.
J
Jermaine WilliamsAug 26, 2025
How to improve RF range on Clear-Com TEMPEST 2400?
- P
  Pamela WoodAug 26, 2025
  To improve the RF range of your Clear-Com Intercom System, try the following: * Position the BaseStation antenna or transceiver as high as possible. * Make sure the BaseStation antenna or transceiver are in an appropriate location and orientation. * Ensure the antenna or transceiver are not near any metal structures or racks. * Check that all antenna connections are secure. * If using multiple Tempest BaseStations nearby, use Accu-Sync. * Set the Network Number for each BaseStation at least four numbers apart.
H
harveydestinyAug 28, 2025
Why does Clear-Com Intercom System headset microphone sound distorted?
- J
  jacobwalkerAug 28, 2025
  If the headset microphone in your Clear-Com Intercom System sounds distorted or cuts off parts of words, this might be the reason: if the microphone gain is set too low, the audio may sound choppy or clip off the first part of words. If the microphone gain is set too high, the audio may sound distorted at higher audio levels.
S
Sandra ContrerasAug 31, 2025
Why no audio passing on Clear-Com Intercom System without external intercom?
- R
  Rebecca CarneyAug 31, 2025
  If there is no audio passing when you're not using an external hard wired intercom system and Tempest BaseStations are sharing intercom channels on your Clear-Com Intercom System, check these: 1. Confirm that no wired intercoms are connected to the system. 2. Confirm a 3-pin XLR cable connection for each channel to be shared, between each of the BaseStations. 3. Set the BaseStation 2-Wire Intercom Type Select Switch to the Clear-Com position. 4. Select 2-Wire for the relevant channels. 5. Ensure only one of the Tempest BaseStations is set to Master Mode.
E
Erin MillerDec 1, 2025
What to do if can't hear channels on Clear-Com TEMPEST 2400?
- S
  Shannon JonesDec 1, 2025
  If you cannot hear one or more channels of a hard wired intercom on your Clear-Com Intercom System, try these steps: 1. Set the Front panel headset to monitor the intercom channel in question. 2. Confirm that the channel is working wirelessly, from the BaseStation to a BeltStation. 3. Confirm that the wired system is working correctly, separately from the Tempest Wireless system. 4. If using a 2-Wire external wired intercom system, make sure that the 2-Wire Intercom Type Select Switch on the front of the BaseStation is in the appropriate position. 5. Ensure that the correct 2-Wire or 4-Wire LED is lit for the intercom channel that you are using. 6. Adjust the IN and OUT level for the appropriate intercom channel. 7. Ensure that all external 2-Wire or 4-Wire hard wired intercom connections...
M
michael32Sep 13, 2025
How to troubleshoot no audio on hardwired intercom channels in Clear-Com TEMPEST 2400 Intercom System?
- J
  Jason RamirezSep 13, 2025
  If you cannot hear one or more channels of hardwired intercom on your Clear-Com Intercom System, set the front panel headset to monitor the channel in question and enable the Talk button. Turn up the headset volume. Confirm the channel works wirelessly from the BaseStation to a BeltStation and that the wired system is working separately. For a 2-Wire system, ensure the 2-Wire Intercom Type Select Switch is correctly set. Check that the correct 2-Wire or 4-Wire LED is lit. Adjust the IN and OUT levels for the channel and ensure all external connections are properly made. Try another cable if needed.
W
Wesley HamiltonSep 10, 2025
What to do if Clear-Com TEMPEST 2400 Intercom System BeltStation will not power up?
- K
  kimberly50Sep 12, 2025
  If your Clear-Com Intercom System BeltStation won't power up, first, check that the batteries are correctly installed. If using a Lithium-Polymer rechargeable battery, ensure it's fully charged. If using alkaline AA batteries, make sure they are fresh and installed correctly, following the diagram in the battery compartment. Finally, press and hold the Power button on the back of the BeltStation for two seconds to power it on.
W
Wayne HarrisSep 7, 2025
Why Stage Announce function does not work on Clear-Com TEMPEST 2400 Intercom System?
- V
  Vanessa OwensSep 7, 2025
  If the Stage Announce (SA) function isn't working properly on your Clear-Com Intercom System, confirm that the Stage Announce function is enabled in the BeltStation and ensure that the Stage Relay is enabled in the BeltStation.