What to do if the 2-W LEDs remain red on my Clear-Com HME DX210 Intercom System?
Plug the system into a 2-W power supply. If you intentionally don't want to use a powered 2-W system, open the base station cover and set JP1 (IC1) and/or JP2 (IC2) to the ON position. Also, when daisy-chaining, remember to terminate one of the base stations by setting JP5 (IC1) and/or JP6 (IC2) to ON. Refer to Appendix C, page 23 for jumper (JP) locations.
Why Clear-Com Intercom System settings are not retained after power cycle?
The internal battery may be low. Contact your dealer.
Why red light on Clear-Com Intercom System base station power switch does not come on?
Ensure that the power cords are properly connected to the base station, power supply, and electrical outlet.
How to eliminate echo on 2-W line in Clear-Com Intercom System?
Ensure that no wired Belt Packs have open mics, that the line is terminated, and rerun Auto Null.
Why is there a loud squeal on my Clear-Com Intercom System when I talk?
This can occur if two or more base stations are daisy-chained without terminating the appropriate channel. To resolve this, set the termination by putting JP5 (IC1) and/or JP6 (IC2) in the ON position in only one base station. Refer to Appendix C, page 22 for jumper (JP) locations.
How to resolve 2-W LEDs remaining red on Clear-Com Intercom System?
Plug into a 2-W power supply. If the absence of a powered 2-W system is intentional (such as when using a Clear-Com MT1, or when daisy-chaining multiple base stations), open the base station cover and set JP1 (IC1) and/or JP2 (IC2) to the ON position. If daisy-chaining, do not forget to also terminate one of the base stations by setting JP5 (IC1) and/or JP6 (IC2) to ON. Refer to Appendix C, page 22 for jumper (JP) locations.
Why are my Clear-Com HME DX210 settings not retained when I turn the base station off and on?
The internal battery may be low. Contact your dealer.
What to do if registration failed on my Clear-Com HME DX210?
If 'F' is displayed in the STATUS display, it means you've tried to register more than 15 Beltpacks. Refer to 'If registration failed' in section 2.3.2, page 9, and repeat the registration procedure. Follow the related instructions in section 2.3.2, page 10.
What to do if I get an echo on the 2-W line on my Clear-Com HME DX210?
Ensure that no wired Beltpacks have open microphones, that the line is terminated, and then rerun Auto Null.
What to do if people on RTS/Clear-Com systems can't hear me on Clear-Com Intercom System?
First, check that the cables are securely connected and that the 2-wire intercom is powered on. If you're using the local headset, ensure the correct IC setting is selected in the HEADSET section on the base station's front panel. If you're using a Belt Pack or All-In-One Headset, press the appropriate IC button.
Details the controls and indicators on the front panel of the BS210 base station.
Instructions for connecting power supplies and charging batteries for the system components.
Guides on connecting antennas, power, and setting the operating mode for the base station.
Covers the initial setup and registration process for beltpacks and headsets with the base station.
Instructions for connecting the system to external 2-wire and 4-wire intercom systems.
Covers base station controls, digital radio functions, indicator lights, and local headset connectivity.
Details operation for beltpacks and headsets, including power, modes, volume, gain, side tone, and battery changes.
General| System Type | Digital Wireless Intercom |
|---|---|
| Frequency Range | 2.4 GHz ISM Band |
| Number of Users | Up to 10 |
| Operating Range | Up to 300 feet (100 meters) in open space |
| Audio Codec | Digital Audio |
| Headset Connector | 4-pin XLR |
| Base Station Power | 100-240V AC, 50/60 Hz |
| Audio Input | XLR |
| Audio Output | XLR |
| Power Supply | AC Adapter |
To Next Page