Code 3 21 Series User Manual

Page 1 of 16
Installation and Operation Instructions
MATRIX-ENABLED
21/27/COVERT SERIES LIGHTBARS
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious bodily/
personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current
arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system
without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, drive
against tra󰀩c, respond at a high rate of speed, or walk on or around tra󰀩c lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations.
The manufacturer assumes no liability for any loss resulting from the use of this warning device.
8. This product may contain high intensity LEDs staring directly into these lights could result in temporary and/or permanent vision
impairment.
Cross Section: Covert Series 1.6” x 12.3”
21 Series 2.1” x 12.3”
27 Series 2.7” x 12.3”
Max Input Voltage: 10-16 VDC
Nominal Input Voltage: 12 VDC
Fusing Requirement: 30A / 60A
Matrix Connectivity: Covert Series CAT5
21 / 27 Series CAT5
Temp. Range: -40ºC to 65ºC
(-40ºF to 149ºF)
Specications:
Light Module Current (@ 12 VDC):
27 Series Prizm Single Color 5 LED AL, WL, RD 0.7 A
27 Series Prizm Single Color 8 LED Directional 1.3 A
27 Series Prizm Single Color 12 LED Directional 1.7 A
27 Series Prizm Dual Color 24 LED Directional 2.0 A
27 Series Prizm Tri Color 24 LED Directional 1.1 A
21 Series Torus Single Color 3 LED AL, WL, TD 0.4 A
21 Series Torus Single Color 3 LED Directional 0.6 A
21 Series Torus Single Color 4 LED Directional 0.8 A
Covert / 21 Series Torus Dual Color 6 LED AL, WL, TD 0.6 A
21 Series Torus Single Color 6 LED Directional 1.1 A
21 Series Torus Single Color 8 LED Directional 1.3 A
Covert / 21 Series Torus Tri Color 9 LED AL, WL, TD 0.6 A
Covert / 21 Series Torus Dual Color 12 LED Directional 1.2 A
Covert / 21 Series Torus Dual Color 16 LED Directional 1.3 A
Covert / 21 Series Torus Tri Color 18 LED Directional 1.2 A
Additional Matrix Resources
Product Information: www.code3esg.com/us/en/products/matrix
Training Videos: www.youtube.com/c/Code3Inc
Matrix Software: http://software.code3esg.global/updater/matrix/downloads/Matrix.exe

Code 3 21 Series Specifications

General

Light Source	LED
Lens Material	Polycarbonate
Voltage	12V DC
Flash Patterns	Multiple
Dimensions	Varies by model
Color Options	Amber, Blue, Red, White, Green
Current Draw	Varies by model
Weight	Varies by model
Certifications	SAE

Summary

Safety Information and Specifications

General Safety Precautions

Essential safety guidelines for installation and operation of emergency warning devices.

Product Specifications

Technical details including dimensions, voltage, and fusing requirements.

Installation and Mounting Procedures

Unpacking and Pre-Installation

Steps for inspecting the product and preparing for installation.

Mounting Options Overview

Details on different mounting methods for the lightbar.

Direct Mount Option

Instructions for mounting the lightbar directly to the vehicle roof.

Pylon/Headache Rack Option

Steps for mounting the lightbar using a pylon or headache rack.

Strap Kit Option

Procedure for installing the lightbar using a strap kit for door frame mounting.

Wiring and Configuration

Wiring Instructions

Guidance on connecting power and serial communication cables.

Flash Pattern Overview

Description of default flash patterns and network configuration.

Flash Pattern Compliance

Data tables for 21/27 Series and Covert Series lightbar flash patterns.

Component Identification

Replacement Parts and Assemblies

Identification of lightbar components, modules, and boards.

Maintenance and Troubleshooting

Maintenance Procedures

Guidelines for cleaning lenses and maintaining the lightbar's condition.

Troubleshooting Guide

Diagnosing and resolving common issues like power, communication, and module errors.

Warranty and Product Returns

Manufacturer Limited Warranty

Details on warranty coverage, exclusions, and limitations of liability.

Product Returns Process

Procedure for returning products for repair or replacement.