Home
ComAp
Controller
IG-NTC GC
ComAp IG-NTC GC User Manual
5
of 1
of 1 rating
260 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
IGS-
NT
-
BC
, S
W
Version 1.2.0
,
©
Com
Ap
–
Januar
y 2019
IGS-
NT
-
BC
-1.2.0 Reference Gui
de.PDF
153
Value: React pwr L3
Group
Bank values
Units
kVAr
Related FW
3.0
Description
Generator reactive po
wer in ph
ase L3.
Value: Appar pwr
Group
Bank values
Units
kVA
Related FW
3.0
Description
Generator total appar
ent po
wer.
Value: Appar pwr L1
Group
Bank values
Units
kVA
Related FW
3.0
Description
Generator apparent
power in phase L1
.
Value: Appar pwr L2
Group
Bank values
Units
kVA
Related FW
3.0
Description
Generator apparent
power in phase L2
.
Value: Appar pwr L3
Group
Bank values
Units
kVA
Related FW
3.0
Description
Generator apparent
power in phase L3
.
Value: Pwr factor
Group
Bank values
Un
its
-
Related FW
3.0
Description
Generator cos-p
hi factor.
N
OTE
:
The "cos-phi" f
actor is widely use
d instead of po
wer factor f
or pure harmonic
waveforms
, because a simplified m
ethod can be used
for calculation of
it's value.
152
154
Table of Contents
Table of Contents
2
Document Information
4
Available Related Documentation
5
General Guidelines
6
What Is Described in this Manual
6
Dangerous Voltage
7
Adjust Set Points
7
Clarification of Notation
7
Available Firmware and Archive Sets
9
Bank Controller - Firmware/Hardware/Archive Compatibility
9
Gen-Set Controller - Firmware/Hardware/Archive Compatibility
9
General Description of System with Bank Controller
10
Installation
11
CAN Bus Wiring
11
Power Lines Wiring
12
AC Measurement
14
BCB Control and Synchronizing
16
Functions
18
OFF-MAN-AUT Mode
18
Active and Reactive Power Control in the System with Bank Controller
19
Power Management in System with Bank Controller
19
Load Shedding
25
Circuit Breakers Operation Sequence, CB Fail Detection
26
Remote Alarm Messaging
31
Controller Redundancy
32
Force Value - Step by Step Guide
33
Values for Continuous Writing from External Sources
35
General Purpose Timers
35
History Related Functions
37
User Buttons
38
Remote Control Function
39
Virtual Peripheral Inputs-Outputs (VPIO) Module
39
Shared Inputs and Outputs
40
Distributed Binary Inputs and Outputs
42
Modbus Reading and Writing
43
User MODBUS
43
Modbus Switches
44
Analog Input Sensors and User Sensors
44
Languages and Translator Tool in Genconfig
45
Power Formats
45
System Start/Stop
45
User Mask Function
46
PLC Functions
47
Multi Language Support
47
ECU Interface Customizing
47
Protections and Alarm Management
49
Configuration of User Configurable Protections in Genconfig
54
Inputs and Outputs
57
Virtual and Physical Modules
57
Setpoints
58
List of Possible Events
59
Controller Configuration and Monitoring
60
Direct Connection to the PC
60
Genconfig Functions
60
Intelimonitor
61
Modbus Protocol
61
Value and Setpoint Codes
61
Technical Data
61
Language Support
61
Setpoint Groups
64
Table of Setpoints
64
Table of Values
151
Table of Binary Input Functions
183
Table of Analog Input Functions
223
Table of Binary Output Functions
225
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the ComAp IG-NTC GC and is the answer not in the manual?
Ask a question
ComAp IG-NTC GC Specifications
General
Brand
ComAp
Model
IG-NTC GC
Category
Controller
Language
English
Related product manuals
ComAp IG-NTC-BB
92 pages
ComAp IG-NT
92 pages
ComAp IG-NT-BB
92 pages
ComAp IGS-NT Series
328 pages
ComAp InteliLite 9
401 pages
ComAp InteliSys NT
44 pages
ComAp InteliGen 200
35 pages
ComAp InteliDrive Lite
92 pages
ComAp InteliLite MRS16
632 pages
ComAp InteliATS NT PWR
69 pages
ComAp InteliLite AMF25
735 pages
ComAp InteliLite MRS11
65 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
