ComAp IS-NTC-BB

To Next Page

To Previous Page

IGS-NT-Combi-3.0 Reference Guide.PDF

List of possible events

The complete list is available in Troubleshooting guide.

Main Page

Table of Contents2
Document Information4
Available Related Documentation5
General Guidelines6
What Is Described in this Manual6
Dangerous Voltage7
Adjust Set Points7
Clarification of Notation8
Available Firmware and Archive Sets9
General Description10
Basic Description of COMBI Application10
Switching the Sptm, SPI and MINT Applications10
Functions12
OFF-MAN-AUT-TEST Mode12
Test on Load (Sptm Application Only)15
Mains Parameters out of Limits During Synchronising (SPI, Sptm Appl.)16
Manual Fuse Synchronizing (Sptm Application Only)16
Baseload Change by Binary Inputs (Sptm or SPI Application)16
Active Power Control Modes in Sptm or SPI Application16
PF Control Modes in Sptm or SPI Application18
Active and Reactive Power Control Modes (MINT Application Only)19
Power Management (MINT Application Only)19
Load Shedding24
Power Derating25
Engine States26
Circuit Breakers Operation Sequence, GCB/MCB Fail Detection34
Peak Shaving Based on Active and Apparent Power (Sptm or SPI Appl.)40
Remote Alarm Messaging40
Controller Redundancy42
Automatic Mains Failure Function in Sptm Application43
Cleaning Mode43
Automaticallocation of Addresses on Intercontroller CAN244
Force Value - Step by Step Guide44
Values for Continuous Writing from External Sources46
General Purpose Timers46
History Related Functions47
User Buttons49
Remote Control Function49
Virtual Peripheral Inputs-Outputs (VPIO) Module50
Shared Inputs and Outputs50
Distributed Binary Inputs and Outputs52
Modbus Reading and Writing53
User MODBUS54
Analog Input Sensors and User Sensors54
Languages and Translator Tool in Genconfig55
Power Formats55
System Start/Stop55
User Mask Function56
PLC Functions57
Multi Language Support57
ECU Interface Customizing57
Protections and Alarm Management58
Configuration of User Configurable Protections in Genconfig65
Gen-Set Operation States68
Inputs and Outputs70
Virtual and Physical Modules70
Setpoints71
List of Possible Events72
Controller Configuration and Monitoring73
Direct Connection to the PC73
Genconfig Functions73
Intelimonitor74
Modbus Protocol74
Value and Setpoint Codes74
Technical Data74
Language Support74
Setpoint Groups77
Setpoints - SMS/E-Mail77
Setpoints - AMF Settings78
Setpoints - Analog Protect78
Setpoints - Basic Settings78
Setpoints - Comms Settings78
Setpoints - Date/Time79
Setpoints - Engine Params79
Setpoints - Engine Protect80
Setpoints - Force Value80
Setpoints - Gener Protect81
Setpoints - Load Shedding81
Setpoints - Power Management81
Setpoints - Mains Protect82
Setpoints - Process Control Single83
Setpoints - Process Control Multi83
Setpoints - Sync/Load Ctrl83
Setpoints - Timer Settings84
Setpoints - Volt/Pf Control84
Value Groups85
Values Group - Analog CU85
Values Group - bin Inputs CU85
Values Group - bin Outputs CU85
Values Group - Engine Values85
Values Group - Force Value85
Values Group - Gener Values86
Values Group - Info86
Values Group - Log Bout87
Values Group - Load Shedding87
Values Group - Mains/Bus Val87
Values Group - Power Management87
Values Group - Statistics88
Values Group - Sync/Load Ctrl88
Values Group - Volt/Pf Ctrl88
Binary Input Functions89
Analog Input Functions91
Binary Output Functions92
Common Functions92
Breaker Control92
Control Loops92
Power Management92
Status Information93
Fixed Protections Output94
Configurable Protection Outputs95
Table of Setpoints95
Table of Values223
Table of Binary Input Functions257
Table of Analog Input Functions302
Table of Binary Output Functions312

Table of Contents

Other manuals for ComAp IS-NTC-BB

Related product manuals