To Next Page
V
Valerie BradySep 23, 2025
Why the table on my Craftex Power Tool cannot be raised?
- Eeileen58Sep 23, 2025
If the table on your Craftex Power Tool cannot be raised, it is likely due to a lack of lubrication. Make sure to lubricate it.
Why the table on my Craftex Power Tool cannot be raised?
If the table on your Craftex Power Tool cannot be raised, it is likely due to a lack of lubrication. Make sure to lubricate it.
What to do if there is no speed readout on my Craftex Power Tool?
If there's no speed readout on your Craftex Power Tool, the speed pickup might be out of adjustment or has failed. Adjust the gap between the speed pickup and the post spindle pulley. If there is still no readout on the speed indicator, replace the speed pickup.
Why doesn't my Craftex Lathe start?
If your Craftex Lathe does not start, or the power supply fuse/breaker trips immediately after start-up, there could be several reasons: * The OFF button might not have been pressed before toggling the spindle direction switch. Press the OFF button before toggling the spindle direction switch. * The motor brushes might be worn or faulty. Remove and replace the brushes. * The fuse might be blown. Replace the fuse and ensure there are no shorts. * The power supply circuit breaker might have tripped, or the fuse might be blown. Ensure the circuit is sized correctly and free of shorts. Reset the circuit breaker or replace the fuse. * The motor wires might be connected incorrectly. Correct the motor wiring connections. * The wiring might be open or have high resistance. Check and f...
Why is my Craftex Power Tool leaving fuzzy grain?
This can be caused by blunt knives, so get new knives. Also, if the wood contains high moisture, let it dry before usage.
What to do if the Craftex CX614 Saw blade sticks in the cut?
If the Craftex Saw blade is sticking in the cut, it could be due to several reasons. You might be advancing too quickly, so try decreasing the advance and using less cutting pressure. Alternatively, the cutting speed might be too low, so try increasing the speed. Ensure you're using a disk with a suitable tooth pitch. Check the blend of lubricating coolant and consider using a better quality disk if there's a sticky accumulation of material. Also, verify the level of lubricating refrigerant in the tank. If the issue persists, increase the flow of lubricating refrigerant, making sure the hole and liquid outlet pipe aren't blocked.
Why is my Craftex CX614 Saw disk vibrating?
If the Craftex Saw disk is vibrating, it could be due to several reasons. The tooth pitch or tooth profile might be unsuitable, so choose a suitable disk. Ensure the part is gripped effectively in the vise. If the dimensions of the solid section are too large, abide by the instructions. If the disk diameter is incorrect or too large, decrease the disk diameter to match the part being cut.
What causes a Craftex CX614 Saw disk to chip?
If your Craftex Saw disk is chipping, it could be due to hardness, shape, or flaws in the material, so reduce the cutting pressure and/or the advance. The cutting speed might be wrong, so change the disk speed and/or diameter. Also, the tooth pitch might be wrong, so choose a suitable disk. Check the gripping of the part if there are vibrations. If the disk is incorrectly sharpened, replace it with one that is more suitable and correctly sharpened. Using a better quality disk might also solve the problem. Finally, check the percentage of water and oil in the emulsion if the lubricating refrigerant is incorrect.
What causes premature disk wear on a Craftex CX614 Saw?
If the Craftex Saw disk is experiencing premature wear, several factors could be responsible. Ensure the disk was correctly run in, referring to the relevant chapter for guidance. The cutting speed might be incorrect, so adjust the disk speed and/or diameter. An unsuitable tooth profile or pitch could also be the cause, so select a suitable disk. Using a better quality disk may help. Also, ensure there is sufficient lubricating refrigerant by checking the level of the liquid in the tank. If the issue persists, increase the flow of lubricating refrigerant, ensuring that the hole and liquid outlet pipe are not blocked.
How to prevent tooth breakage on my Craftex CX614?
If your Craftex Saw is experiencing tooth breakage, it could be due to several factors. You might be advancing too fast, so decrease the advance and use less cutting pressure. The cutting speed could be wrong, so change the disk speed and/or diameter. Ensure you're using a disk with the correct tooth pitch and of better quality. Check the gripping of the part in the vise. Remove any broken tooth parts left in the cut. Avoid resuming cutting on a previously made groove by turning the part. Check the level of lubricating liquid in the tank. Increase the flow of lubricating refrigerant, checking that the hole and the liquid outlet pipe are not blocked, and ensure the lubricating coolant is properly blended.
What to do if Craftex Air Cleaner has insufficient suction?
If your Craftex Air Cleaner isn't providing enough suction, the inlet port might be blocked, so try cleaning it. Also, the filter bag could be full; in that case, empty it. Finally, check if the outlet port is blocked and clean it, or adjust the outlet's direction.
General
