Crown 2/600 - Universal Switching Power Supply

91 pages

To Next Page

To Previous Page

Page 61

CDi DriveCore Series Operation Manual

System Protection

Universal Switching Power Supply

The CDi DriveCore Series ampliﬁers incorporate a switching power supply designed for extremely high efﬁciency and high output power. The supply

includes Power Factor Correction (PFC) and a Series Resonant Converter (SRC), and accepts AC supply voltages from ~100V to ~240V. Microprocessor-

controlled diagnostic and control capabilities both optimize performance and enhance long-term reliability.

Main Page

Default Chapter1
- Operation Manual1
- Power Amplifiers1
- Table of Contents2
Welcome3
- Features3
- How to Use this Manual3
Installing the Amp4
- Unpacking4
- Additional Materials4
- Installing the Amplifier4
- Proper Cooling4
Front Panel Overview5
Rear Panel Overview6
Hardware Setup7
- Connecting the AC Power Cord7
- Power up Procedure7
- Precautions8
- Wiring Input Connectors9
- Wiring Output Connectors9
Front Panel Menus & Navigation Overview10
- Menu Structure10
- The Home Screen11
Adjusting Channel Volume12
Configuring the Amp13
- Using the Guided Setup13
- Configuring Inputs & Outputs14
- Configuring DSP18
Installing Audio Architect & Configuring the Network23
- Introduction to Hiqnet Audio Architect23
- Configuring Amplifier Network Settings24
Using Hiqnet Audio Architect31
- Offline & Online Operation Explained31
- Going Online32
  - Matching Devices32
- Main CDI Drivecore Control Panel33
- Amplifier Information34
- Configuring Inputs & Outputs in Audio Architect35
- Crossover Panel40
  - FIR Filters40
- Input/Output EQ Panels41
- Input/Output Delay Panels42
- Levelmax Panel43
  - About the Transducer Thermal Limiter43
- Signal Generator Panel44
- Managing Device & Preset Files45
Application Examples47
- Dual Mode, Low Z (8Ω, 4Ω, or 2Ω)47
- Bridge Mono Mode, Low Z (16Ω, 8Ω, or 4Ω)48
- Dual Mode, High Z (70Vrms/100Vrms)49
- Bridge Mono Mode, High Z (140Vrms/200Vrms)50
Using BLU Link51
- BLU Link Specifications51
- BLU Link Latency51
- Making BLU Link Connections51
- BLU Link Port LED Indicators52
- Mastership53
- Fault Tolerance53
- BLU Link Status54
Device Presets55
- Saving Device Presets55
- Loading Device Presets56
System Settings57
- Lighting/Display Options57
- Security/Front Panel Lockout58
- Amplifier Diagnostics59
- Amp Gain Mode59
Using the GPIO Control Port60
- GPIO Pinout, Specification, Use, & Configuration60
Using the AUX Port61
- Sleep61
- Amp Status61
System Protection62
- Faults62
- Thermal Limit62
- Auto-Insertion High-Pass Filters62
- AC Under/Over-Voltage Protection62
- Fan-Cooled Chassis62
- Universal Switching Power Supply63
Troubleshooting64
Signal Path Block Diagram66
Factory Reset67
Specifications68
- Output Power: Dual Mode - All Channels Driven68
- Output Power: Bridge Mono Mode - All Channels Driven68
- Input Sensitivity68
- Performance Specifications69
- Dimensions70
Warranty (United States Only)71
Service72
- Worldwide Service72
- US and Canada Service72
- Service at a US or Canada Service Center72
- Factory Service72
- Factory Service Shipping Instructions73
- Packing Instructions73
- Estimate Approval73
- Payment of Non-Warranty Repairs73
Service Return Authorization Request74
Open Source Disclaimer for HARMAN Products75
GNU General Public License Version 278
GNU General Public License Version 383

Related product manuals

Crown PowerTech PT 2.1

Crown Micro-Tech 2401

39 pages

Crown XLS 2500 Series

8 pages

Crown 2/600 - Universal Switching Power Supply

Table of Contents

Related product manuals