Daikin EWAA011DAV3P - Page 233

7/10
Breadcrumb Field code Setting name Range, step
Default value
Date Value
Field settings table
Installer setting at variance with
default value
9.I [2-0C] R/W
0: Underfloor heating
1: Fancoil unit
2: Radiator
9.I [2-0D] R/W
0: Underfloor heating
1: Fancoil unit
2: Radiator
9.I [2-0E] R/W 20~50 A, step: 1 A
50
A
9.I [3-00] R/W 0: No
1: Yes
9.I [3-01]
0
9.I [3-02]
1
9.I [3-03]
4
9.I [3-04]
2
9.I [3-05]
1
9.I [3-06] R/W 18~30°C, step: 1°C
30°C
9.I [3-07] R/W 12~18°C, step: 1°C
12°C
9.I [3-08] R/W 25~35°C, step: 1°C
35°C
9.I [3-09] R/W 15~25°C, step: 1°C
15°C
9.I [4-00] R/W 0: Disabled
1: Enabled
2: Onl
y
DHW
9.I [4-01] R/W
0: None
1: BSH
2: BUH
9.I [4-02] R/W 14~35°C, step: 1°C
with BUH:
35°C
without BUH:
25°C
9.I [4-03] R/W 0: Restricted
1: Allowed
2: Overlap
3: Compressor off
4: Le
g
ionella onl
y
9.I [4-04]
0: Intermittent (not to be used)
1: Continuous
2: Of
f
9.I [4-05]
0
9.I [4-06] R/W 0: Manual
1: Automatic(normal SH/DHW ON)
2: Auto red SH/DHW ON
3: Auto red SH/DHW OFF
4: SH ON/DHW OFF
9.I [4-07]
6
9.I [4-08] R/W
0: No limitation
1: Continuous
2: Di
g
ital in
p
uts
9.I [4-09] R/W 0: Current
1: Power
9.I [4-0A] R/W
0: 1
1: 1/1+2
2: 1/2
3: 1/2 + 1/1+2 in emer
g
enc
y
9.I [4-0B] R/W 1~10°C, step: 0,5°C
1°C
9.I [4-0D] R/W 1~10°C, step: 0,5°C
3°C
9.I [4-0E]
6
9.I [5-00] R/W 0: Allowed
1: Not allowed
9.I [5-01] R/W -15~35°C, step: 1°C
0°C
9.I [5-02] R/W
0: Disabled
1: Enabled
9.I [5-03] R/W -15~35°C, step: 1°C
0°C
9.I [5-04] R/W 0~20°C, step: 1°C
10°C
9.I [5-05] R/W 0~50 A, step: 1 A
50
A
9.I [5-06] R/W 0~50 A, step: 1 A
50
A
9.I [5-07] R/W 0~50 A, step: 1 A
50
A
9.I [5-08] R/W 0~50 A, step: 1 A
50
A
9.I [5-09] R/W 0~20 kW, step: 0,5 kW
20 kW
9.I [5-0A] R/W 0~20 kW, step: 0,5 kW
20 kW
9.I [5-0B] R/W 0~20 kW, step: 0,5 kW
20 kW
9.I [5-0C] R/W 0~20 kW, step: 0,5 kW
20 kW
9.I [5-0D] R/W
0: 230V, 1~
1: 230V, 3~
2: 400V, 3~
9.I [5-0E]
1
9.I [6-00] R/W 2~40°C, step: 1°C
27°C
9.I [6-01] R/W 0~10°C, step: 1°C
2°C
9.I [6-02] R/W 0~10kW, step: 0,2kW
0kW
9.I [6-03] R/W 0~10kW, step: 0,2kW
0kW
9.I [6-04] R/W
0~10kW, step: 0,2kW
0kW
The temperature difference determining the heat pump OFF temperature.
What is the capacity of the booster heater?
What is the capacity of the backup heater step 1?
What is the capacity of the backup heater step 2?
What is the requested limit for DI2?
What is the requested limit for DI3?
What is the requested limit for DI4?
Backup heater voltage
--
The temperature difference determining the heat pump ON temperature.
Set point correction for domestic hot water temperature.
What is the requested limit for DI1?
What is the requested limit for DI2?
What is the requested limit for DI3?
What is the requested limit for DI4?
What is the requested limit for DI1?
Automatic cooling/heating changeover offset.
--
Is backup heater operation allowed above equilibrium temperature during space
heating operation?
What is the equilibrium temperature for the building?
Space heating priority.
Space heating priority temperature.
Emergency
--
Which power limitation mode is required on the system?
Which power limitation type is required?
Backup heater configuration
Automatic cooling/heating changeover hysteresis.
What is the BUH operation mode?
Which electric heater has priority?
Below which outdoor temperature is heating allowed?
Operation permission of the booster heater.
Water pipe freeze prevention
--
--
--
What is the maximum desired room temperature in heating?
What is the mimimum desired room temperature in heating?
What is the maximum desired room temperature in cooling?
What is the minimum desired room temperature in cooling?
What emitter type is connected to the additional LWT zone?
What is the maximum allowed current over the heatpump ?
Is auto restart of the unit allowed?
--
--
--
What emitter type is connected to the main LWT zone?
(*1) EWAA*
(*2) EWYA*
(#) Setting is not applicable for this unit. 4P627274-1 - 2020.09