ED34-862 Accessories
FXFQ-P 91
2
KDBH55K160(F) — Sealing Material of Air Discharge Outlet
KDBH55K160
Dimensions Unit:mm
Sealing materials for long air outlets (Polyethylene foam t10): 2 pieces Sealing materials for horizontal blades (Polyethylene foam t10): 8 pieces
Slit
Slit
Sealing materials for air outlets at the corner (Polyethylene foam t10): 1 piece for each
Tape for sealing materials
for long air outlets (Non-woven fabric t0.6): 2
Tape for sealing materials
for air outlets at the corner (Non-woven fabric t0.6): 3
Tape for sealing materials
for air outlets at the corner (Non-woven fabric t0.6): 1
Side insulation plate (NB foam t10) : 2
Antisweat material (Flocking tape): See right
Antisweat material (Flocking tape): See right
Applicable part number
Applicable part number
Q'ty and colour
4, grey
4 for each, Dark grey or black
Q'ty and colour
4, grey
4 for each, Dark grey or black
J : 1P177350A
C
1
3
2
3
2
2
4
3
1
2
3
4
1
2
3
3
1
2
B1
1
4
2
2
3
2
4
3
1
42 2
1
4
3
4
4
1
1
33
1
2
3
1
4
3
1
2
2
2
1
2
4
3
2
3
1
2
4
1
3
11
3
4
1
1
4
4
4
1
4
2
3
2
1
B2
4
3
1
3
22
4
3
2
1
3
4
4
3
4
4
4
2
(12)
(12)
()()
(12)
A
D
(12)
3
(12)
(12)
(12)
(12)
(12)
Field Setting
Blow Direction Selection and Sealing Material Mounting
(1) Blow direction selection
Depending on the installation location, select a blow direction from the table below. For the setting position number, refer to
For the selection of installation location, refer to the installation manual attached to the indoor unit's main body.
Precautions
Blow direction patterns other than those shown in the figure below cannot be selected. (Condensation may occur.)
Air outlet 2
Air outlet B1, B2
Air outlet A
Air outlet 1
Air outlet D
Air outlet 3
Air outlet C
Air outlet 4
Drain side
Pipe side
Drain side
Pipe side
4-way
4-way 3-way
3-way 2-way
2-way
(2) Matching with the corner air outlets A to D that are to be blocked, stick the sealing material to the tape for fixing the sealing material.
(Stick the sealing material so that the sealing material comes to the positions shown in the schematic diagram.)
Sealing material 2
Release paper
Procedure 1
Remove the
release paper.
Tape for fixing the sealing material
8
Air outlet A
Procedure 2
Stick the sealing material to the
tape for fixing the sealing material.
Sealing material 3
Tape for fixing the sealing material 8
Air outlet
B1
When the indoor unit's main
body belongs to classes 28 to 56
Sealing material 5
Tape for fixing the sealing material 8
Air outlet C
Sealing material 4
Tape for fixing the sealing material 8
Air outlet
B2
Air outlet D
Sealing material 6
When the indoor unit's main body
belongs to classes 63 to 160
Tape for fixing the sealing material 9
Air outlet
Indoor unit main body
Indoor unit main body
With air outlets B to D , using the same procedure,
stick the sealing material to the tape for fixing the sealing material as shown in the figure.
The sealing material has a directional property. Be sure to stick the sealing material to the tape for fixing the sealing material so that the printed number of outlet to be blocked becomes visible.
When blocking both the air outlet 1 and air outlet D , start the sticking of sealing material with the air outlet D .
(4) Matching the longitudinal air outlet numbered 1 to 4 that are to be blocked, prepare the sealing material and tape for fixing the sealing material.
Cut both the sealing material and tape for fixing the sealing material along the perforation (dotted line).
Stick the sealing material to the tape for fixing the sealing material.
(Stick so that the sealing material comes to the centre of tape for fixing the sealing material.)
Example) When blocking air outlet 2 or 3
Sealing material 1
4
2
3
Procedure 2
Remove the
release paper.
Procedure 1
Cut off
Tape for fixing the sealing material 7
Procedure 3
Stick the sealing material so that it comes
to the centre of tape for fixing the sealing material.
Release paper
<Sealing material treatment>
• When blocking the air outlet 1 , the sealing material preparation is not necessary.
The sealing material has a directional property. Be sure to stick the sealing material to
the tape for fixing the sealing material so that the printed number of outlet to be blocked becomes visible.
Air outlet 1
(5) Stick the sealing material that was prepared in
(4) to the air outlet of indoor unit main body.
<Mounting to air outlet>
Precautions
.
Precautions
(3) Stick the sealing material that was prepared in
(2) to the air outlet of indoor unit main body.
Все каталоги и инструкции здесь: http://splitoff.ru/tehn-doc.html
To Next Page
Loading...
