What does 'Broken Belt' mean on Danfoss VLT CDS 803?
The 'Broken Belt' message on Danfoss DC Drives means the torque is below the torque level set for no load, indicating a broken belt. See parameter group 22-6* Broken Belt Detection.
What does 'Inverter over-load' mean on Danfoss VLT CDS 803 DC Drives?
An 'Inverter over-load' message on Danfoss DC Drives means the drive has experienced more than 100% load for an extended period.
What does 'Earth Fault' mean on Danfoss DC Drives?
An 'Earth Fault' on Danfoss DC Drives suggests a discharge from output phases to ground.
What does Ctrl. word TO mean in Danfoss DC Drives?
This indicates a loss of communication to the frequency converter. See parameter group 8-0* General Settings for troubleshooting.
What does 'Locked rotor' mean on Danfoss VLT CDS 803 DC Drives?
The 'Locked rotor' message on Danfoss DC Drives means the rotor is locked or the load is too high.
What does 'AMA big motor' mean on Danfoss DC Drives?
The message 'AMA big motor' on Danfoss DC Drives indicates that the motor is too big to perform AMA.
What does 'Current limit' mean on Danfoss VLT CDS 803?
If your Danfoss DC Drives display the message 'Current limit', it means the current is higher than the value set in parameter 4-18 Current Limit.
How to fix 'Live zero error' on Danfoss VLT CDS 803 DC Drives?
A 'Live zero error' occurs when the signal on terminal 53 or 54 is less than 50% of the value set in parameter 6-10 Terminal 53 Low Voltage, parameter 6-12 Terminal 53 Low Current, parameter 6-20 Terminal 54 Low Voltage, or parameter 6-22 Terminal 54 Low Current. See also parameter group 6-0* Analog I/O Mode.
What does 'AMA small mot' mean on Danfoss DC Drives?
The message 'AMA small mot' on Danfoss DC Drives indicates that the motor is too small to perform AMA.
What does 'Illegal FC configuration' mean on Danfoss VLT CDS 803 DC Drives?
The message 'Illegal FC configuration' on Danfoss DC Drives indicates that the control card and power card are not matched.
Details guide purpose, supplementary documentation, and software support.
Lists manual/software versions and product approvals/certifications.
Explains safety symbols and requirements for qualified personnel.
Details essential safety measures for hazardous voltage and unintended starts.
Highlights hazards like discharge time, leakage, equipment contact, and internal failures.
Introduces the CDS 803 family, listing common I/Os and communication features.
Details specialized functions for compressor systems like Secure Start-up and speed detection.
Details custom application functions like AMA, PID control, and Smart Logic Control.
Details built-in protection functions for mains input, output, temperature, and internal faults.
Explains the Ecodesign Directive for energy-related products in Europe.
Presents detailed electrical specs for 3x200-240V and 3x380-480V AC systems.
Details mains supply parameters and compressor output voltage.
Lists specifications for all control inputs, outputs, relays, and communication.
Specifies ambient conditions, environmental requirements, and conforming standards.
Details cable lengths, acoustic noise sources, and mechanical dimensions.
Presents dU/dt data including cable length, voltage, and rise time.
Provides guidelines for safe handling, storage, and capacitor reforming.
Details side-by-side clearance, operating environment, gases, dust, and humidity.
Explains derating due to ambient temperature, switching frequency, and high altitudes.
Presents derating curves for various power ratings based on temperature and frequency.
Describes the optional IP21/NEMA Type 1 enclosure kit for enhanced protection.
Covers general installation, cable specs, and fuse/breaker recommendations.
Details wiring schematics, terminal layouts, and connection procedures.
Guides IT grid installations and details relay terminal configurations.
Guides on configuring RS485 serial communication for drives.
Discusses EMC, interference sources, requirements, and compliant installation.
Provides instructions for EMC-compliant installation and cable selection.
Explains RFI filter usage and discusses harmonics emission.
Details galvanic isolation, PELV requirements, and ground leakage current.
Provides guidelines for using RCDs for leakage current protection.
Guides to the online configurator and explains the type code structure for ordering.
Lists available accessories and spare parts with their respective order numbers.
Provides a comprehensive glossary of abbreviations used in the manual.
Explains conventions used for lists, bold, and italic text in the document.
To Next Page
General