Datalogic Matrix 400 User Manual (English)

Other manuals for Datalogic Matrix 400

Manual86 pages

Quick Reference Guide20 pages

Questions and Answers:

V
vspenceAug 17, 2025
What to do if my Datalogic Card Reader is not transmitting to the host?
- J
  Jeffery JonesAug 17, 2025
  If the Datalogic Card Reader isn't transmitting data to the host, verify that the serial cable is correctly wired. If you're using a CBX, make sure the RS485 termination switch is OFF. Also, ensure that the host serial port settings match the reader's serial port settings. The "COM" LED in the VisiSet™ Digital I/O folder can be configured to indicate MAIN COM port TX or MAIN COM port RX.
M
Mark RobertsonAug 20, 2025
What to do if Datalogic Card Reader always transmits the No Read Message?
- M
  molly27Aug 20, 2025
  If the Datalogic Card Reader always transmits the No Read Message, try running the Rapid Configuration procedure. Position the reader correctly using the guidelines in par. 3.3 and the VisiSet™ Calibration Tool. Adjust the ACQUISITION TRIGGER DELAY if the moving code is out of the reader's field of view. If no external trigger source is available, set the Continuous Operating Mode. Enhance the code image quality by tuning the IMAGE ACQUISITION SETTING. Check the parameter settings in the Decoding, 2D Codes, 1D Codes, and Postal Codes folders. Finally, view the full-resolution code image to assess the printing or marking quality.
K
Kiara SandersAug 23, 2025
What to do if the image from Datalogic Card Reader is focused but not decoded?
- G
  Gabriel PhillipsAug 23, 2025
  If the image from your Datalogic Card Reader is focused but not decoded, verify the Calibrate Image Density procedure.
J
John OlsonAug 26, 2025
Why is the data transferred to the host incorrect, corrupted or incomplete from Datalogic Card Reader?
- G
  gilesnancyAug 26, 2025
  If the data transferred to the host from the Datalogic Card Reader is incorrect, corrupted, or incomplete, check the settings of the Header and Terminator String parameters in the VisiSet™ Communication folder. Also, check the settings of the DATA FORMAT parameter group in the VisiSet™ Data Collection folder.
M
Michael CrawfordAug 28, 2025
What to do if the trigger LED is blinking but no result is transmitted by Datalogic Card Reader?
- L
  Linda AllenAug 28, 2025
  If the ”TRIGGER” LED is correctly blinking on your Datalogic Card Reader in any operating mode, but no result is transmitted at the end of the reading phase collection, check the settings for the CODE COLLECTION, DATA FORMAT and STATISTICS parameter groups in the Data Collection folder.
D
dickersonmichaelAug 31, 2025
What to do if the trigger LED is not blinking on Datalogic Card Reader?
- K
  Kristy LopezAug 31, 2025
  If the ”TRIGGER” LED is not blinking on the Datalogic Card Reader in Continuous Mode, verify the correct software configuration settings.
J
jkellerSep 3, 2025
Why is no image displayed in VisiSet™ if the trigger LED is blinking on Datalogic Card Reader?
- S
  Sergio EverettSep 3, 2025
  If the ”TRIGGER” LED is correctly blinking in Phase Mode on the Datalogic Card Reader, but no image is displayed in the VisiSet™ Calibration Tool window, determine if the Phase frequency is lower than the maximum frame rate.
K
Karen SandersSep 5, 2025
How to troubleshoot Datalogic Card Reader if the power LED is not lit?
- R
  rmartinezSep 5, 2025
  If the “POWER” LED is not lit on the Datalogic Card Reader, check the following: 1. Is the power connected? 2. If using a power adapter (like PG6000), is it connected to a wall outlet? 3. If using rail power, does the rail have power? 4. If using CBX, does it have power (check switch and LED)? Also, check if you are referring to the M16 19-pin connector or to the CBX spring clamp connectors. Measure Voltage either at pin A and pin L (for 19-pin connector) or at spring clamp Vdc and GND (for CBX).
M
martineztoddSep 8, 2025
How to fix a blurry image on Datalogic Card Reader?
- S
  Stephanie AllenSep 8, 2025
  If the image from your Datalogic Card Reader is not clear, verify the Focus procedure.