dataTaker DT80 - Page 36

UM-0085-B09 DT80 Range User Manual Page 36
RG
Category
Channel
Type
Signal\ Sensor Details
Default Channel
Options
Channel
Factor
Output
Units
More Information
Time, Date
and System
Timers
1ST
2ST
3ST
4ST
writable
System timers
Increment every
sec (1ST), min (2ST),
hour (3ST), day (4ST)
(60)
(60)
(24)
(7)
range
Counts
System Timers (P39)
Delay
DELAY
writable
Delays
schedule execution for
nominated time
ms
Delay (P39)
Note 6
System Data
SV
some are
writable
System variable
scaling
factor
System Variables (P40)
Variables
CV
writable
Channel variables: general
purpose holders for data,
calculation results
scaling
factor
Channel Variables (nCV)
(P67)
IV
Integer variables
scaling
factor
Rainflow Cycle Counting
(P79)
Calculation
CALC
writable
Temporary holder for
calculation result
scaling
factor
Calculation Only Channels
(P69)
Reference
&name
Last measurement value for
channel called name
scaling
factor
Reference Channels (P69)
Text
$
writable
General purpose text for
headings, etc. (max. 80
characters each)
Text (P38)
Serial
SERIAL
Transmit to and receive from
serial device
(P53)
ie. P53 specifies
default timeout
timeout
(sec)
State
Generic Serial
Channel(P348)
SDI12
Control SDI-12 sensors using
digital channels 5-8
(AD0,R1)
scaling
factor
SDI-12 Channel (P342)
SSPORT
writable
Enable/disable serial sensor
port (not DT81)
delay (ms)
Note 6
State
Serial Interface Power
Control (P357)
Modbus
MODBUS
Read/control Modbus sensors
(MBI,MES,TO3,
RT0)
scaling
factor
Modbus Channel (P361)
Power Output
PWR12V
writable
Enable/disable 12V power
output (Series 2,3,4)
delay (ms)
Note 6
State
Controlling 12V Power
Output (P290)
PWR5V
writable
Enable/disable isolated 5V
power output (Series 3 only)
delay (ms)
Note 6, 7
State
Controlling 5V Isolated
Power Output(P291)
PWR_OUT
writable
Enable/disable 12/ 5V 350
mA output (Series 4 only)
delay (ms)
Note 6, 7
State
Controlling 12V/ 5V Power
Output (P290)
VDAC
writable
VDAC 16-bit analog output
(Series 4 only)
mV
Signal Output (P291)
IDAC
writable
IDAC 16-bit analog
output (Series 4 only)
mA
Signal Output (P291)
Digital
Input
DS
Digital state input (1 bit)
State
Digital Inputs (P332)
DN
Digital nybble input (4 bits)
(15)
bit mask
Note 5
Nybble
DB
Digital byte input (8 bits)
(255)
bit mask
Note 5
Byte
AS
Digital state input on an
analog channel
(2500)
threshold
(mV)
State
Analog Logic State Inputs
(P330)
Digital Output
DSO
writable
Output on a single digital
channel.
delay (ms)
Note 6
State
Digital Outputs (P333)
DNO
writable
Nybble output on a group of
digital channels
(15)
bit mask
Note 5
Nybble
DBO
writable
Byte output on a group of
digital channels
(255)
bit mask
Note 5
Byte
RELAY
writable
1=Relay output closed
0=Relay output open
delay (ms)
Note 6
State
WARN
writable
1=Attn LED on
0=Attn LED off
delay (ms)
Note 6
State
Counter
C
writable
Pulse count on digital input (0
to range-1)
range
Counts
Counters – Low Speed
(P337)
HSC
writable
High Speed Up Counter (0 to
range-1)
range
Counts
Counters – High Speed
(P338)