dataTaker DT80 - Page 387

UM-0085-B09 DT80 Range User Manual Page 387
RG
HRESET
generate a hardware reset of the DT80
273
INIT
clear current job and reset settings to power-on defaults
273
IP
return DT80 IP address
233
IPGW
return default gateway IP address
233
IPSN
return subnet mask
233
LISTD
option
=
value option
=
value..
return store file details
98
LOCKJOB jobspec
prevent specified job(s) from being overwritten when a new job is entered
63
LOG "string"
save a user specified message to the event log
276
LOGOFF
switch off data/alarm logging for all schedules
94
LOGOFF
sched
switch off data/alarm logging for schedule sched
94
LOGON
switch on data/alarm logging for all schedules
94
LOGON
sched
switch on data/alarm logging for schedule sched
94
MODEM
sub-command
low level diagnostics for integrated modem
218
NAMEDCVS
return current values of all named channel variables
69
NTP
attempt to set time from NTP server
270
P
n
return the current value of parameter n
260
P
n=value
set parameter n to value
260
PASSWORD
return 1 if a comms interface password is set, otherwise 0
186
PASSWORD="
password
"
set comms interface password
186
PAUSE
value
delay for value ms
90
PH
return current host RS232 port parameters
195
PH=
baudrate
,
databits
,
parity
,
stopbits
,
flow
set host RS232 port parameters (all parameters are optional)
195
PING
hostname
send echo request to specified host computer
221
PROFILE
return current settings for all profile keys
264
PROFILE
section
return current settings for all profile keys in section
264
PROFILE
section key
return current value of specified profile key
264
PROFILE section key=
set specified profile key to default
264
PROFILE section=
set all profile keys in section to defaults
264
PROFILE
section key
=
keystring
set specified profile key to keystring
264
PS
return current serial sensor port parameters
198
PS=mode,baudrate,databits,parity,stopbits,
flow
set serial sensor port parameters (all parameters are optional)
198
Q
terminate an unload
110
RAINFLOWmaxcyc:rej%:m..nIV
return a rainflow analysis report
79
REMOVEMEDIA
stop using a USB memory device so it can be safely removed
115
RENAME
src dest
rename file/folder src to dest (src may also be an FTP URI)
116
RESET
(obsolete) same as
INIT
273
RUNJOB "
jobname
"
replace current job with specified job
62
RUNJOBONINSERT "
jobname
"
create ONINSERT.DXC for this
DT80
on USB memory device
64
RUNJOBONINSERTALL "jobname"
create global ONINSERT.DXC on USB memory device
64
Sn=a,b,c,d"units"
define span #n (all parameters other than a and b are optional)
65
SATTN
set Attn LED
123
SDI12SEND
sdi-chan
"
sdi-cmd
"
send the specified SDI-12 command
343
SERVICEDATA {filename}
generate service report; optionally write to specified file
277
SESSION
command
communications session diagnostics
227
SETDIALOUTNUMBER "phonenum"
set the number to call when DIAL command is issued
203
SETMODBUS channels format scaling
define data formats used when communicating with Modbus client system
178
SHOWPROG
jobspec
return the program text for the specified job(s)
63
SIGNOFF
end authenticated user session (password required to reconnect)
259
SIGNON
start authenticated user session
259
SINGLEPUSH
(obsolete) same as
HRESET
273
SSDIRECT port "terminator"
forward all subsequent commands, terminated by specified string, to serial
channel port (1=serial sensor, 2=host RS232)
356
STATUS
return a status report
276
STATUS
n
return line n of the status report
276
STATUS14 "jobname"
return internal details about specified job
276
Tn=a,b,c"units"
define thermistor scaling function #n (all parameters other than a are
optional)
66