Denon AVP-A1HD - User Manual

Other manuals for Denon AVP-A1HD

Product Compatibility Chart1 page

Product Review16 pages

Questions and Answers:

M
Matthew JohnstonAug 27, 2025
How to troubleshoot no picture with HDMI on Denon Amplifier?
- G
  George MitchellAug 27, 2025
  If no picture is appearing when using HDMI connections on your Denon Amplifier, verify that the HDMI connections are correctly and securely connected. Check the HDMI input setting. Ensure that your monitor is compatible with copyright protection (HDCP). Also, make sure that the HDMI format of both the player and the monitor match. If you've set the output to “Auto (Dual)”, try setting it to either “Monitor 1” or “Monitor 2”, as the display may not be correct in “Auto (Dual)” mode depending on the monitor you have connected.
B
benjamin90Aug 28, 2025
What does it mean when my Denon AVP-A1HD power turns off and the indicator flashes red?
- T
  Todd BlackwellAug 28, 2025
  If your Denon Amplifier suddenly turns off and the power indicator flashes red, the set may be damaged. Turn off the power and contact a DENON service center.
J
Jimmy MooreAug 28, 2025
How to get HDMI audio from Denon Amplifier speakers?
- F
  fullerelizabethAug 29, 2025
  If your Denon Amplifier isn't outputting HDMI audio signals from the speakers, check the “Manual Setup” – “HDMI Setup” – “Audio” setting. If it's set to “TV”, change it to “Amp.”
C
Christopher BaileyAug 29, 2025
Why can't I play Internet radio on my Denon AVP-A1HD?
- S
  Shannon ThompsonAug 29, 2025
  If your Denon Amplifier is not playing Internet radio, verify that the Ethernet cable is properly connected and that your network is connected. Note that only Internet radio programs in MP3 and WMA formats can be played. Check your computer’s or router’s firewall settings to ensure they are not blocking the connection. Also, the radio station might not be currently broadcasting, so try another station. Finally, check the amplifier's IP address to ensure it is correct.
E
eric63Aug 30, 2025
What to do if no picture appears on my Denon AVP-A1HD Amplifier?
- E
  elizabethparkerAug 30, 2025
  If no picture appears on your Denon Amplifier, check the connections between the unit and the monitor. Ensure the monitor’s input setting is correct. If PURE DIRECT mode is enabled, disable it. If you're using component input connectors for the player and video (yellow) or S-Video output connectors for the monitor, note that high definition (1080i/720p) and progressive (480p/576p) video signals are not down-converted; set the player to interlace (480i/576i) signals.
K
Katherine GrahamAug 30, 2025
How to fix on-screen display not appearing on Denon AVP-A1HD?
- J
  Joe CruzAug 30, 2025
  If the on-screen display does not appear on your Denon Amplifier, the format of the GUI and TV (NTSC or PAL) may not match. Make sure the GUI and TV formats are the same.
V
Virginia CochranAug 25, 2025
How to fix a Denon AVP-A1HD remote control that is not working?
- M
  Mary JonesAug 25, 2025
  If your Denon Amplifier's remote control isn't working, try these steps: First, replace the batteries with new ones. Make sure you are operating the remote within its specified range and that there are no obstacles blocking the signal. Ensure the batteries are inserted correctly, matching the polarity marks in the battery compartment. Move the amplifier to a location where the remote control sensor isn't exposed to strong light. Finally, ensure that the remote IDs are the same for both the main unit and the remote control unit.
J
Jessica MooreSep 1, 2025
Why can't I connect to preset radio stations on my Denon AVP-A1HD Amplifier?
- A
  Andrew GriffithSep 1, 2025
  If you cannot connect to preset or favorite radio stations on your Denon Amplifier, the radio station may not be currently broadcasting or may no longer be in service. Wait a while before trying again, but note that stations that are no longer in service cannot be connected to.
J
Jillian HahnSep 1, 2025
Why is there no sound from my Denon AVP-A1HD Amplifier surround back speaker?
- A
  Amber WattsSep 1, 2025
  If no sound is produced from your Denon Amplifier's surround back speaker, the surround back speaker setting might be set to “None”. Change it to something other than “None”. Also, confirm that the surround mode is set to a mode for 6.1- or 7.1-channel playback; select an appropriate surround playback mode.
T
Tanya PriceSep 2, 2025
What does “Server Full” mean on my Denon Amplifier radio?
- L
  Leah RiveraSep 2, 2025
  If you are experiencing issues with some radio stations displaying “Server Full” or “Connection Down” on your Denon Amplifier, it could be due to the station being congested or not currently broadcasting. Wait a while before trying to connect again.

Denon AVP-A1HD Specifications

General

Receiver type	Surround
Input sensitivity	200 mV
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.005 %
Power output per channel (1KHz@6 Ohm)	170 W
Power output per channel (20-20KHz@8 Ohm)	- W
RS-232 ports	2
Connectivity technology	Wired
Speakers connectivity type	XLR
Multichannel pre out connectivity	RCA
Ethernet LAN	Yes
Supported radio bands	-
Optical drive included	No
HDMI version	1.3a
Product color	Silver
Audio decoders	Dolby Surround, DTS-HD
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	Not supported
HDMI in	6
Audio (L/R) in	10
Composite video in	8
Digital audio optical in	5
Ethernet LAN (RJ-45) ports	1
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.3 W
Power consumption (typical)	150 W
Composite video out	3
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG