To Next PageTo Next PageWhy is the display turned off on my Denon Receiver?
If the display on your Denon Receiver is off, it could be due to one of two reasons: either the “Display” setting is set to “OFF”, or the PURE DIRECT mode is activated. To resolve this, change the “Display” setting to something other than “OFF”. Alternatively, select a surround mode other than the PURE DIRECT mode.
How to enable subwoofer output on my Denon Stereo Receiver?
If you’re not getting any sound from the subwoofer connected to your Denon Stereo Receiver, check these things: * Make sure the subwoofer is powered on. * Verify that the “Subwoofer” setting at “Speaker Config.” is set to “Yes”. * Ensure the subwoofer is properly connected. * Adjust the subwoofer’s volume to an appropriate level.
What to do if my Denon AVR-1910 doesn't respond to the remote control?
If your Denon Receiver isn't responding to the remote, try these steps: First, replace the batteries with new ones. Ensure you are operating the remote within its specified range and that there are no obstacles between the remote and the receiver. Verify the batteries are inserted correctly, matching the polarity marks in the battery compartment. Strong light may interfere with the remote control sensor, so move the unit to a location away from direct sunlight or bright lights. Lastly, ensure the DEVICE SELECT switch on the remote matches the settings on the receiver.
Why are the surround speakers not working on my Denon Stereo Receiver?
If you're not getting any sound from the surround speakers on your Denon Stereo Receiver, it might be because the surround mode is set to “STEREO”, “DIRECT” or “PURE DIRECT”. To resolve this, set the receiver to a surround playback mode.
Why is there no sound from the center speaker on my Denon Stereo Receiver?
If there is no sound from the center speaker on your Denon Stereo Receiver, and you are playing a monaural source (like TV) in “STANDARD” (Dolby/DTS Surround) mode, change the mode to something other than “STANDARD” (Dolby/ DTS Surround).
How to fix no sound from my Denon Stereo Receiver speakers?
If no sound is coming from the speakers of your Denon Stereo Receiver, check the following: * Ensure the connections to the input devices and speaker cables are correct. * Verify that the selected input source matches the device you are trying to play. * Increase the master volume to an audible level. * Deactivate mute mode. * Disconnect any connected headphones. * Confirm digital signals are being input, and the input mode is correctly set.
Why is there no sound from surround back speaker on my Denon AVR-1910?
If there's no sound coming from the surround back speaker on your Denon Receiver, check these settings: Ensure the surround back speaker’s power amplifier is correctly assigned to the appropriate channel. Verify that the “S.Back” setting is not set to “None”. Confirm that the “Parameter” – “Surround Parameter” – “SB CH Out” settings are not set to “OFF”. Lastly, ensure the surround mode is set to a mode that supports 6.1- or 7.1-channel playback. Adjust these settings as needed.
How to fix no sound from surround speakers on Denon AVR-1910?
If there is no sound coming from the surround speakers connected to your Denon Receiver, ensure that the surround mode is set to a surround playback mode and not “STEREO”, “DIRECT” or “PURE DIRECT”.
Why no sound from center speaker on my Denon AVR-1910 Receiver?
If no sound is coming from the center speaker of your Denon Receiver, and you are playing a monaural source (like TV) in “STANDARD” (Dolby/DTS Surround) mode, change the mode to something other than “STANDARD” (Dolby/ DTS Surround).
How do I fix Denon AVR-1910 Receiver not outputting DTS sound?
If your Denon Receiver isn't outputting DTS sound, there are a few things to check: First, ensure that the Blu-ray Disc player / DVD player’s audio output setting is not set to bitstream. Next, confirm that your Blu-ray Disc player / DVD player is compatible with DTS sound playback. Lastly, make sure the AVR-1910’s “Decode Mode” setting is set to “Auto” or “DTS”, and not “PCM”.
General| Speakers connectivity type | - |
|---|---|
| Receiver type | Surround |
| Frequency range | 10 - 100000 Hz |
| Audio output channels | 7.1 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.08 % |
| Power output per channel (1KHz@6 Ohm) | 125 W |
| Power output per channel (20-20KHz@8 Ohm) | 90 W |
| Equalizer | Yes |
| Product color | Black |
| Audio decoders | DTS-HD Master Audio, Dolby Pro Logic IIz, Dolby TrueHD |
| Apple docking compatibility | iPod |
| Optical drive included | No |
| AM band range | 520 - 1710 kHz |
| FM band range | 87.5 - 107.9 MHz |
| Supported radio bands | AM, FM |
| AC input voltage | 120 V |
| AC input frequency | 60 Hz |
| Power consumption (standby) | 0.3 W |
| HDMI in | 4 |
| S-Video inputs quantity | 1 |
| Component video (YPbPr/YCbCr) in | 2 |
Weight and Dimensions| Depth | 171 mm |
|---|---|
| Width | 434 mm |
| Height | 377 mm |
| Weight | 10700 g |
