EasyManuals Logo

Denon AVR-1910 Service Manual

Denon AVR-1910
153 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #53 background imageLoading...
Page #53 background image
53
AVR-1910/1620/1610/790/590
K4S641632K (IC30 : for AVR-1910)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
54Pin TSOP (II)
(400mil x 875mil)
(0.8 mm Pin pitch)
PIN FUNCTION DESCRIPTION
Pin Name Input Function
CLK System clock Active on the positive going edge to sample all inputs.
CS
Chip select
Disables or enables device operation by masking or enabling all inputs except
CLK, CKE and DQM
CKE Clock enable
Masks system clock to freeze operation from the next clock cycle.
CKE should be enabled at least one cycle prior to new command.
Disable input buffers for power down in standby.
A
0 ~ A11 Address
Row/column addresses are multiplexed on the same pins.
Row address : RA0 ~ RA11,
Column address : (x8 : CA
0 ~ CA8 , x16 : CA0 ~ CA7)
BA
0 ~ BA1 Bank select address
Selects bank to be activated during row address latch time.
Selects bank for read/write during column address latch time.
RAS
Row address strobe
Latches row addresses on the positive going edge of the CLK with RAS
low.
Enables row access & precharge.
CAS
Column address strobe
Latches column addresses on the positive going edge of the CLK with CAS
low.
Enables column access.
WE
Write enable
Enables write operation and row precharge.
Latches data in starting from CAS
, WE active.
DQM Data input/output mask
Makes data output Hi-Z, t
SHZ after the clock and masks the output.
Blocks data input when DQM active.
DQ
0 ~ N Data input/output
Data inputs/outputs are multiplexed on the same pins.
(x8 : DQ
0 ~ 7), (x16 : DQ0 ~ 15)
V
DD/VSS Power supply/ground Power and ground for the input buffers and the core logic.
V
DDQ/VSSQ Data output power/ground
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
N.C/RFU
No connection
/reserved for future use
This pin is recommended to be left No Connection on the device.
x16
x8
x16
x8
VDD
DQ0
V
DDQ
DQ1
DQ2
V
SSQ
DQ3
DQ4
V
DDQ
DQ5
DQ6
V
SSQ
DQ7
V
DD
LDQM
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
V
DD
VSS
DQ15
V
SSQ
DQ14
DQ13
V
DDQ
DQ12
DQ11
V
SSQ
DQ10
DQ9
V
DDQ
DQ8
V
SS
N.C/RFU
UDQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
V
SS
VDD
DQ0
V
DDQ
N.C
DQ1
V
SSQ
N.C
DQ2
V
DDQ
N.C
DQ3
V
SSQ
N.C
V
DD
N.C
WE
CAS
RAS
CS
BA0
BA1
A10/AP
A0
A1
A2
A3
V
DD
VSS
DQ7
V
SSQ
N.C
DQ6
V
DDQ
N.C
DQ5
V
SSQ
N.C
DQ4
V
DDQ
N.C
V
SS
N.C/RFU
DQM
CLK
CKE
N.C
A11
A9
A8
A7
A6
A5
A4
V
SS

Table of Contents

Other manuals for Denon AVR-1910

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-1910 and is the answer not in the manual?

Denon AVR-1910 Specifications

General IconGeneral
Speakers connectivity type-
Receiver typeSurround
Frequency range10 - 100000 Hz
Audio output channels7.1 channels
Signal-to-Noise Ratio (SNR)100 dB
Total Harmonic Distortion (THD)0.08 %
Power output per channel (1KHz@6 Ohm)125 W
Power output per channel (20-20KHz@8 Ohm)90 W
EqualizerYes
Product colorBlack
Audio decodersDTS-HD Master Audio, Dolby Pro Logic IIz, Dolby TrueHD
Apple docking compatibilityiPod
Optical drive includedNo
AM band range520 - 1710 kHz
FM band range87.5 - 107.9 MHz
Supported radio bandsAM, FM
AC input voltage120 V
AC input frequency60 Hz
Power consumption (standby)0.3 W
HDMI in4
S-Video inputs quantity1
Component video (YPbPr/YCbCr) in2
Weight and Dimensions IconWeight and Dimensions
Depth171 mm
Width434 mm
Height377 mm
Weight10700 g

Related product manuals