Denon AVR-3310 User Manual


Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Setting items Setting contents
Bass Setting
Settings for subwoofer and
LFE signal range playback.
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
LFE : The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
This can be set when “Speaker Configuration” – “Subwoofer” (vpage
33) is set to “Yes”.
Play music or a movie source and select the mode offering the strongest
bass.
Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
•
•
•
•
•
LPF for LFE : Set LFE signal playback range.
80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz•
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Unit : Set the unit of distance.
Feet
Meters
•
•
Step : Set the minimum variable width of the distance.
0.1m / 0.01m
1ft / 0.1ft
•
•
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
S. Back L
z
/ S. Back R
z
/ Front Height L / Front Height R : Select the
speaker.
z: When the “Speaker Configuration” – “Surround Back” setting
(vpage 33) is set to “1spkr”, “S. Back” is displayed.
0.00m ~ 18.00m / 0.0ft ~ 60.0ft : Set the distance.
Speakers set to “None” in “Speaker Configuration” (vpage 33) are
not displayed.
The speakers that can be selected differ depending on the “Amp Assign”
(vpage 33) and “Speaker Configuration” (vpage 33) settings.
Default settings :
Front / Center / Subwoofer / Front Height : 3.60 m (12.0 ft)
Surround / Surround Back : 3.00 m (10.0 ft)
Set the difference in the distance between the speakers to less than 6.0
meters (20 feet).
•
•
•
•
•
Making Detailed Settings (Manual Setup)
Setting items Setting contents
Distance
(Continued)
Default : Reset all distance settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press ENTER.
•
•
Channel Level
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone Start : Output test tone.
Front L / Front Height L / Center / Front Height R / Front R / Surround
R / S. Back R
z
/ S. Back L
z
/ Surround L / Subwoofer : Select the
speaker.
z
: When the “Speaker Configuration” – “Surround Back” setting
(vpage 33) is set to “1spkr”, “S. Back” is displayed.
–12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Speakers set to “None” in the “Speaker Configuration” (vpage 33)
settings are not displayed.
When o is pressed while the subwoofer volume is set to “–12 dB”, the
“Subwoofer” setting switches to “OFF”.
When a headphones jack is inserted in the PHONES terminal of the AVR-
3310, the “Channel Level” is not displayed.
You can also press [CHANNEL LEVEL] to set (vpage 76 “Adjust the
Volume of the Different Speakers“).
•
•
•
•
•
•
Default : Reset all channel level settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
•
•
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Settings

Denon AVR-3310 Specifications

General

Equalizer	Yes
Product color	Black
Frequency range	10 - 100000 Hz
Total Harmonic Distortion (THD)	0.05 %
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
Connectivity technology	Wired
Headphone connectivity	3.5 mm
S-Video outputs quantity	2
Digital audio optical out	1
S-Video inputs quantity	7
Digital audio optical in	3
Dimensions (WxDxH)	434 x 414 x 171 mm
HDMI ports quantity	5
Power consumption (standby)	1 W
Power consumption (typical)	780 W

Weight and Dimensions

Weight	12900 g