Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Setting items Setting contents
HDMI Control
External devices can be
controlled from the AVR-
4310 and the AVR-4310 can
be controlled from external
devices.
Please consult the
operating instructions for
each connected device to
check the settings.
Refer to “HDMI Control
Function” (vpage 77) for
more information about the
HDMI control function.
When the “Control”
setting has been changed,
always turn off the power
to the connecting devices
afterwards and then turn
back on.
NOTE
The HDMI control function
controls operations of a
TV that is compatible with
the HDMI control function.
Make sure that the TV and
HDMI are connected when
you perform HDMI control.
•
•
•
Control
ON : Use HDMI control function
OFF : Do not use HDMI control function
When a device that is not compatible with the HDMI control function
is connected, set “Control” to “OFF”.
NOTE
When “Control” is set to “ON”, it consumes more standby power.
When not using this unit for a long period, we recommend that you
press <POWER> on the main unit to turn off the power.
“HDMI Control” does not work when the power to the equipment is off.
Either power on or set to standby.
•
•
•
•
•
Standby Source : Set the HDMI connector for HDMI signal input during
standby.
Last : Standby with last used input source during power on.
HDMI1 / HDMI2 / HDMI3 / HDMI4 / HDMI5 / HDMI6 : The standby mode
is set at the input source assigned to the respective.
This can be set when “Control“ is set to “ON“.
•
•
Control Monitor : Set the HDMI MONITOR terminal to output the HDMI
control signal.
Monitor 1 : Output from the MONITOR 1 terminal.
Monitor 2 : Output from the MONITOR 2 terminal.
This can be set when “Control“ is set to “ON“.
•
•
Power Off Control : The power of the AVR-4310 and external device turn
off together.
ON : Interlock.
OFF : Do not interlock.
This can be set when “Control“ is set to “ON“.
•
•
Making Detailed Settings (Manual Setup)
See overleaf
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Setting items Setting contents
EXT. IN Setup
Setup playback method for
analog signals inputted from
external input connectors
(EXT. IN).
Surround Speaker : Set the surround speakers to use during playback in
EXT. IN mode.
A : Use surround speakers A.
B : Use surround speakers B.
A+B : Use surround speakers A and B.
Can be set when the “Speaker Configuration” – “Surround A” or
“Surround B” setting (vpage 34) is “Large” or “Small”.
•
•
•
Subwoofer Level : Set playback level of subwoofer signal input from the
external input connector (EXT. IN).
+15dB : This is the recommended level.
+10dB / +5dB / 0dB : Select the level according to the player being
used.
•
•
2ch Direct/Stereo
Make speaker settings for 2-
channel mode playback.
Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
Basic : The settings at “Speaker Setup” (vpage 33) are applied.
Custom : Make separate settings for 2-channel.
•
•
Front : Set the front speaker size.
Large : Use of a large speaker that can adequately playback low
frequencies.
Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
If “Speaker Configuration” – “Subwoofer” (vpage 33) is set to
“No”, the setting is automatically set to “Large”.
•
•
Subwoofer : Set the presence of a subwoofer.
Yes : Use a subwoofer.
No : Select when a subwoofer is not connected.
If “Speaker Configuration” – “Subwoofer” (vpage 33) is set to
“No”, the setting is automatically set to “No”. If the “Front” setting is
“Small”, the setting is automatically “Yes”.
•
•
Make settings for audio playback.
Making the Audio Settings (Audio Setup)
Default settings are underlined.
Settings
To Next Page
Loading...
Need help?
General
Weight and Dimensions
