Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
Making Detailed Settings (Manual Setup)
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Setting items Setting contents
GUI
Make GUI related settings.
Screensaver : Make screensaver settings.
ON : The screen saver is activated during GUI menu display or NET/USB
/ iPod / TUNER screen display if no operation is performed approximately
for a continuous 3-minute period. When you press uio p, the screen
saver is cancelled and the screen before that screen saver started is
displayed.
OFF : Screen saver is not activated.
•
•
Wall Paper : Set wallpaper to display the background when playback is
stopped, etc.
Picture : Set the background to a picture (DENON logo).
Black : Set the background to black.
Gray : Set the background to gray.
Blue : Set the background to blue.
•
•
•
•
Format : Set the video signal format to be output for the TV you are
using.
NTSC : Select NTSC output.
PAL : Select PAL output.
The “Format” can also be set by the following procedure. However,
the GUI screen is not displayed.
1. Press and hold the <DSX> and <RETURN> for at least 3 seconds.
“Video Format” appears on the display.
2. Press o p and set the video signal format.
3. Press the <ENTER>, <MENU> or <RETURN> to complete the
setting.
NOTE
When a format other than the video format of the connected TV is set, the
picture will not be displayed properly.
•
•
Text : Display the content of operation during switching of surround mode,
input mode, etc.
ON : Turn display on.
OFF : Turn display off.
•
•
Master Volume : Master volume display during adjustment.
Bottom : Display at the bottom.
Top : Display at the top.
OFF : Turn display off.
When the master volume display is hard to see when superimposed
on movie subtitles, set to “Top”.
•
•
•
NET/USB : Set the NET/USB screen display time when the input source
is “NET/USB”.
Always : Show display continuously.
30s : Show display for 30 seconds after operation.
10s : Show display for 10 seconds after operation.
OFF : Turn display off.
•
•
•
•
See overleaf
Setting items Setting contents
Volume Control
Set the MAIN ZONE volume
setting.
Volume Display : Set how volume is displayed.
Relative : Display ---dB (Min), in the range –80 dB ~ 18 dB.
Absolute : Display in the range 0 (Min) ~ 99.
The “Volume Display” setting is applied also to the “Volume Limit” and
“Power On Level” display method.
The “Volume Display” setting applies to all zones.
•
•
•
•
Volume Limit : Make a setting for maximum volume
OFF : Do not set a maximum volume.
–20dB (61) / –10dB (71) / 0dB (81)
•
•
Power On Level : Define the volume setting that is active when the
power is turned on.
Last : Use the memorized setting from the last session.
– – – (0) : Always use the muting on condition when power is turned on.
–80dB ~ 18dB (1 ~ 99) : The volume is adjusted to the set level.
•
•
•
Mute Level : Set the amount of attenuation when muting is on.
Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
•
•
•
Source Delete
Remove input sources
that are not used from the
display.
PHONO / CD / DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX / NET/
USB / TUNER : Select input source that is not used.
ON : Use this source.
Delete : Do not use this source.
NOTE
Input sources being used in the various zones cannot be deleted.
Input sources set to “Delete” cannot be selected using SOURCE
SELECT.
•
•
•
•
To Next Page
Loading...
Need help?
General
Weight and Dimensions
