EasyManua.ls Logo

DeVilbiss CVI - User Manual

DeVilbiss CVI
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Service Bulletin
SB-2-658-D
Replaces SB-2-658-C
OPERATION MANUAL
CVi LIGHTWEIGHT GRAVITY FEED SPRAYGUN
English: Pages 3-10
GUIDE D’UTILISATION
PISTOLET PULVÉRISATEUR LÉGER À ALIMENTATION PAR GRAVITÉ CVi
Français: Pages 19-25
MANUAL DE OPERACIÓN
CVi PISTOLA PULVERIZADORA LIGERO POR GRAVEDAD
Español: Páginas 11-18

Table of Contents

Questions and Answers

  • K
    Kelly HoltSep 2, 2025
    Why is my DeVilbiss CVI giving a jerky spray?
    • W
      watsontammySep 2, 2025
      A jerky or fluttering spray from your DeVilbiss Paint Sprayer can stem from several issues. The fluid tip or seat might be loose or damaged, the baffle seal could be installed incorrectly, the material level might be too low, or the container might be tipped too far. Also, there could be an obstruction in the fluid passage, or the fluid needle packing nut might be dry or loose. Try tightening or replacing the fluid tip/seat, installing the baffle seal correctly, refilling the material, holding the container more upright, backflushing with solvent, and lubricating or tightening the fluid needle packing nut.
  • K
    kaiserloriAug 31, 2025
    How to deal with excessive fog from my DeVilbiss Paint Sprayer?
    • D
      David WrightAug 31, 2025
      Excessive fog from your DeVilbiss Paint Sprayer could be due to using too much or too fast-drying thinner, or having too much atomization air pressure. Try remixing the material properly and reducing the pressure.
  • R
    rmillerAug 29, 2025
    How to prevent runs and sags when using my DeVilbiss CVI Paint Sprayer?
    • M
      Michele MathewsAug 29, 2025
      To prevent runs and sags when using your DeVilbiss Paint Sprayer, it's important to manage the material flow and consistency. Adjust the gun or reduce the fluid flow to avoid applying too much material. Ensure the material is properly mixed, or apply light coats. Also, hold the gun at a right angle to the work surface and use the proper gun technique.
  • H
    Howard HernandezAug 28, 2025
    What causes a starved spray pattern with my DeVilbiss CVI?
    • D
      David VazquezAug 28, 2025
      A starved spray pattern with your DeVilbiss Paint Sprayer is typically due to inadequate material flow or low atomization air pressure. To resolve this, back the fluid adjusting screw out to the first thread, or change to a larger tip size. Also, increase the air pressure and rebalance the gun.
  • S
    Sharon ScottAug 27, 2025
    Why is my DeVilbiss CVI producing a split spray pattern?
    • P
      Paul WarnerAug 27, 2025
      A split spray pattern from your DeVilbiss Paint Sprayer can be caused by a few things. The atomization air pressure might be too high, the fluid flow might be too low, or the spreader adjusting valve might be set too high. To correct this, reduce the air pressure, increase the fluid flow, and adjust the spreader valve.
  • O
    ohillAug 25, 2025
    What to do if my DeVilbiss Paint Sprayer is causing dry spray?
    • C
      Christopher FloresAug 25, 2025
      If your DeVilbiss Paint Sprayer is producing a dry spray, it could be due to several factors. The air pressure might be too high, the gun tip might be too far from the work surface, or your gun motion might be too fast. Also, the gun might be out of adjustment. Try reducing the air pressure, adjusting to the proper distance, slowing down your motion, and making any necessary adjustments to the gun.
  • M
    Mr. Michael KellerAug 22, 2025
    How to reduce overspray with my DeVilbiss CVI?
    • C
      cody27Aug 22, 2025
      To reduce excessive overspray with your DeVilbiss Paint Sprayer, first, try reducing the atomization air pressure. Second, adjust the distance between the gun and the work surface to the proper range. Lastly, make sure you are moving the gun at a moderate pace, parallel to the work surface, avoiding arcing motions.

DeVilbiss CVI Specifications

General IconGeneral
Nozzle Size1.3mm
TypeHVLP (High Volume Low Pressure)
Fluid DeliveryGravity Feed
Air Inlet Size1/4 inch
Operating Pressure29 PSI

Related product manuals