What to do if nothing appears on the screen when the power is turned on for DLAB Laboratory Instruments Laboratory Equipment?
If nothing appears on the screen of your DLAB Laboratory Instruments Laboratory Equipment when you turn it on, the building power circuit breaker may have tripped. Remove the cause of the issue and turn the power back on. Alternatively, the fuse may have blown out, in which case you should replace the fuse.
Why does the E-04 Temperature fault alarm code appear on DLAB Laboratory Instruments Laboratory Equipment?
If an E-04 Temperature fault alarm code appears on the time display screen of your DLAB Laboratory Instruments Laboratory Equipment, it could be due to blocked air inlets. Clean the air inlets. Alternatively, the radiator fan may be damaged, requiring a replacement.
What to do if E-02 Door fault alarm code appeared on DLAB Laboratory Instruments D3024 Laboratory Equipment?
If an E-02 Door fault alarm code appears on the time display screen of your DLAB Laboratory Instruments Laboratory Equipment, it could be that the door was opened during operation. Close the door immediately. It could also mean that the button was pressed while the door was opening. In this case, close the door and then start the operation.
General| Brand | DLAB Laboratory Instruments |
|---|---|
| Model | D3024 |
| Category | Laboratory Equipment |
| Language | English |
Follow manual instructions, read safety messages, and understand signal words for safe operation.
Important warnings about potential hazards during operation and handling.
Warnings against explosive samples, flammable gases, wet hands, and electrical shocks.
Cautions on centrifuge placement, door operation, moving, and chamber maintenance.
Cautions on rotor condition, speed limits, imbalance, capacity, and tightening.
Instructions for stopping operation during abnormalities and handling earthquake damage.
Details maximum speed, RCF, capacity, temperature range, motor, dimensions, and weight.
Lists safety and EMC standards, and associated EU and Canadian guidelines.
Specifies power, ambient temperature, humidity, and absence of vibration or hazardous gases.
Outlines acceptable temperature and humidity ranges for transporting and storing the centrifuge.
Details requirements for table surface, ambient temperature, spacing, and avoiding heat/water sources.
Instructions for connecting the power cord safely and ensuring proper grounding.
Illustrates the front and rear external components of the D3024 model.
Illustrates the front and rear external components of the D3024R model.
Details the components of the operation panel, including display areas and indicators.
Explains the main interface of the D3024, showing speed, temperature, and time settings.
Explains the functions of the Pulse, Door, Select, Start/Stop, and Parameter buttons.
Details how to interpret the main interface display for D3024, including speed, temperature, and time.
Instructions for preparing samples, loading tubes, and keeping tubes balanced.
Guidance on inspecting the rotor for damage and proper loading procedures.
Cautions regarding not leaning, keeping chamber clean, and stopping for strange noises.
Describes the steps for starting normal operation, including power on and self-checking.
Explains the display of accumulated running time and last running parameters.
Shows the last set speed, running time, and chamber temperature after self-checking.
Detailed instructions on how to load, secure, and tighten the rotor and its lid.
Guide on using the operation panel to set speed, time, and temperature.
Steps to start the centrifuge, including door locking and timing initiation.
How to check and modify parameters and interpret alarm/error codes.
Procedures for stopping the centrifuge, opening the door, and recalling parameters.
Instructions for operating the centrifuge using RCF values.
How to use the pulse button for brief runs to remove residual samples.
Instructions for cleaning the centrifuge body, rotor chamber, drive shaft, and door.
Procedures for rotor maintenance, cleaning, greasing, and draining the D3024R.
Lists consumable parts like seal rings and rubber blocks, and their replacement conditions.
Detailed instructions on how to replace the seal rings in the rotor.
Guidelines for performing regular checks on stability and grounding.
Lists common symptoms, causes, and solutions for centrifuge errors displayed on the screen.
Instructions for opening the door during normal operation and in case of power outage.
Details on identifying and replacing fuses for both D3024 and D3024R models.
Illustrates the structure of the rotor and identifies its main parts.
Lists compatible rotors and adapters with their specifications like speed, radius, and RCF.
Provides notices on sample density, preventing corrosion, cleaning, autoclaving, and maintenance.
Instructions for cleaning and sterilizing different types of centrifuge tubes.
Details methods for sterilizing PA, PC, and PP tubes using various cleaning fluids and techniques.
Information on the life expectancy of plastic tubes based on usage and care, including a warning against cracked tubes.
Provides the formula and definitions for calculating Relative Centrifugal Force (RCF).
Lists available centrifuge models with their part numbers, plugs, and specifications.
Lists compatible rotors and adapters with their part numbers and descriptions.
Details the warranty period for the centrifuge and rotor, and conditions that void the warranty.
Provides contact details for Dragon Laboratory Instruments Limited for maintenance and service.
To Next Page
