Outputs
The 3G4010 has four programmable outputs to activate in response to the associated events. Refer to the 3G4010 Wiring Dia-
gram (Figure 2) at the back of this manual.
Activating the Outputs
The 3G4010 has four open collector outputs capable of a maximum of 50mA. Internal events on the 3G4010 can trigger the
outputsto turn on an LED or activate an input on the host panel. The default settings are as follows.
OUTPUT 1 Landline Trouble - Output is normally high and will switch to ground when the telephone line is down.
OUTPUT 2 Cellular Module or Network Trouble - Output is normally high and will switch to ground when the 3G4010 can not
communicate with the 3G or 2G network.
OUTPUT 3 Power Supply or Battery Trouble - Output is normally high and will switch to ground when there is a problem with
the power source.
OUTPUT 4 General Module Trouble - Output is normally low and will switch to high when a Cellular Network Trouble, Power
Supply/Battery Trouble, and/or a Failure to Communicate (FTC) trouble is detected.
NOTE: PGM4 must be connected to the control panel as shown in Figure 4 (Residential applications) or Figures 8-9 (Com-
mercial applications). Program the control panel input Zone/Point as 24hr ‘Supervisory’ with keypad-only notification when
activated. Output 4 on the 3G4010 must be set as ‘Active High’.
NOTE: Once an output has been activated automatically,it will not restore its state until all the causes of activation are cleared.
Reporting Codes
3G4010 Reporting Codes CID SIA Programmable Comments
Zone 1 Activation E11A 991 FA 991 YES Delayed 24 Hour Fire *
Zone 1 Restoral R11A 991 FH 991 YES Delayed 24 Hour Fire Restore *
Zone 2 Activation E12A 992 PA 992 YES Panic Alarm *
Zone 2 Restoral R12A 992 PH 992 YES Panic Alarm Restore*
Zone 3 Activation E13A 993 BA 993 YES Burglary *
Zone 3 Restoral R13A 993 BH 993 YES Burglary Restore *
Zone 4 Activation E3AA 994 YX 994 YES System Trouble *
Zone 4 Restoral R3AA 994 YZ 994 YES System Trouble Restore *
PSTN Line Down E351 000 LT 000 FIXED Telco 1 Fault
PSTN Line Restoral R351 000 LR 000 FIXED Telco 1 Fault Restore
Input Loss E337 000 YP 000 FIXED Power Supply Trouble
Input Restoral R337 000 YQ 000 FIXED Power Supply Trouble Restore
Low Battery Alert E338 000 YT 000 FIXED Transmitter Battery Trouble
Low Battery Restoral R338 000 YR 000 FIXED Transmitter Battery Restore
Periodic Test E603 XXX RP XXX FIXED Test Transmission <Receiver Path>
Periodic Test with Trouble E608 XXX RY XXX FIXED Test Transmission <Receiver Path>
Radio Activation R552 000 RS 000 FIXED Remote Programming Successful
Internal Buffer Full E624 000 JL 000 FIXED
FTC Restoral R354 000 YK 000 FIXED Communications Restored
Firmware Update Successful R901 000 LS 000 FIXED
Firmware Update Fail E902 000 LU 000 FIXED
Firmware Update Begin E901 000 LB 000 FIXED
System Tamper E145 000 ES 000 FIXED Expansion Module Tamper
System Tamper Restore R145 000 EJ 000 FIXED Expansion Module Tamper Restore
* C24 Communications default value
Swinger Shutdown
To prevent "runaway" signals to the central station, the 3G4010 is equipped with Swinger Shutdown which limits certain trouble
events to a maximum of four reports every 24 hours.The condition will restore and the counter will reset at midnight. Swinger
Shutdown applies to the following trouble conditions:
l System Tamper/Restore
l Low Battery Trouble/Restore
l TLM Trouble/Restore
12
To Next Page
Loading...
