EasyManua.ls Logo

Duplo DBM-100 - User Manual

Duplo DBM-100
64 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
STAPLER FOLDER
DBM-100
INSTRUCTION MANUAL

Questions and Answers

  • D
    David HoffmanAug 1, 2025
    Why Duplo Folding Machines size lamps blink when turned on?
    • L
      Lisa AllenAug 1, 2025
      This blinking indicates that the power was interrupted during memory processing of a previously used paper size. To resolve this, recall the desired size.
  • K
    Kara YatesAug 5, 2025
    What to do if Duplo DBM-100 paper jams after stapling?
    • J
      John Porter MDAug 5, 2025
      If paper jams after stapling, try these steps: Ensure the stapler and clincher positions are aligned. Lower the side joggers and then reattach them.
  • B
    Benjamin StevensonAug 9, 2025
    What to do if my Duplo DBM-100 Folding Machines DC-10 does not start?
    • M
      moranheidiAug 9, 2025
      If the DC-10 does not start, check the monitor lamp and perform inspections accordingly. Also, ensure the machine is closed and set to automatic mode. Memorize the setting with the memory key.
  • I
    ismithAug 14, 2025
    Why is cover sheet damaged in Duplo Folding Machines?
    • V
      vwoodAug 14, 2025
      Cover sheet damage may occur if the press roller is dirty, so clean it. When binding 64 g/m2 paper, use paper above 80 g/m2 for the cover.
  • D
    David WoodAug 18, 2025
    What to do if Duplo DBM-100 staple has jammed?
    • D
      Derek OrtizAug 18, 2025
      If the staple has jammed, the staple cartridge may not be attached properly. Reset it to resolve the issue.
  • M
    Monica DeanAug 23, 2025
    What to do if Duplo DBM-100 paper is not stapled at the center?
    • C
      Cassandra GrimesAug 23, 2025
      Adjust the clearance with the clearance adjusting plate. To increase the feeding amount, use a metallic ball. To decrease the feeding amount, use a plastic ball. Finely adjust the width between the stoppers.
  • J
    Jill SmithAug 27, 2025
    Why Duplo DBM-100 Folding Machines paper does not infeed the folding plate?
    • B
      Benjamin ColemanAug 27, 2025
      If the paper does not feed into the folding plate, check if the leading edge of the paper is curled upwards (within 6 mm) and straighten it. If the clearance adjusting plate is set too narrow, set the clearance widely.

Summary

Safety Precautions

Usage Precautions

Power Supply

Details about the required voltage and frequency for the unit.

Operating Environment

Recommended temperature and humidity for optimal operation.

Names and Operation of Parts

Control Panel

Explanation of buttons, lamps, and their functions on the control panel.

Binding Operations

Setting the Staple Position

Procedures for adjusting the stapler and clincher positions.

Adjusting Press Roller Clearance

How to adjust the press roller gap for folding operations.

Setting Paper Size and Stapling Method

Instructions for selecting paper sizes and binding methods.

Raising Binding Accuracy

Fine-tuning settings for precise stapling and folding.

Paper Jam Handling

Paper Jam Locations and Clearing Procedures

Steps to clear paper jams from different areas of the unit.

Troubleshooting Guide

Duplo DBM-100 Specifications

General IconGeneral
BrandDuplo
ModelDBM-100
CategoryFolding Machines
LanguageEnglish

Related product manuals