DX Engineering DXE-MBVE-5A - Parts Listings for DXE-MBVE-5 A-UGHW; Optional Accessory Items

- 43 -
DXE-MBVE-5A-UGHW
SAF-T-TILT™ Base Assembly Upgrade Hardware Kit
DXE-MBVE-5A-UGHW for the extended base tube option
Qty
Drawing
Ref.
Number
1/4”-20 x 3/4” long Hex Head Bolt, Stainless Steel
1
18
1/4”-20 x 2-3/4” long Hex Head Cap Screw, Stainless Steel
1
23
1/4”-20 x 3-1/4” long Hex Head Cap Screw, Stainless Steel
2
17
1/4” Flat Washer, Stainless Steel
11
19
1/4” Split Lock Washer, Stainless Steel
6
20
1/4" External Tooth Washer, Stainless Steel
3
21
1/4”-20 Hex Nut, Stainless Steel
6
22
1/4”-20 x 3” long Hex Head Cap Screw, Stainless Steel
2
25
1/2”-13 Hex Nut, Stainless Steel
1
11
1/2”-13 x 4-1/2” long, Hex Head Bolt, Stainless Steel
2
12
1/2” Flat Washer, Stainless Steel, Thick
1
13
1/2” External Tooth Washer, Stainless Steel
2
14
1/2” Split Lock Washer, Stainless Steel
1
15
1/2”-13 Flanged Nut, Stainless Steel
1
16
7” Wire, 14 ga PVC insulated, two 1/4” Ring Terminals
1
24
(Reference Page 32 for drawing)
Optional Accessory Items
JTL-12555 Jet-Lube
™
SS-30 Pure Copper Anti-Seize 12555
Jet-Lube
™
SS-30 Pure Copper Anti-Seize is the top choice of engineers and technicians in government, industry and leading Amateur
Radio contest stations, for protecting mechanical assemblies of aluminum tubing, general hardware and copper grounding
systems. On bonded metal surfaces Jet-Lube
™
SS-30 assures electrical and RF conductivity while preventing oxidation
and corrosion. Surpassing the capabilities of other aluminum anti-oxidants, the wide temperature range of Jet-Lube
™
SS-
30 prevents long-term drying and caking, and allows easy disassembly and effortless cleaning of parts. An
environmentally preferred thread lubricant and conductive termination compound, Jet-Lube
™
SS-30 helps keep your
equipment in serviceable condition. It contains a high concentration of copper flakes, a requirement for heavy loads or
compression; controlled frictional characteristics allow the surfaces of nuts and bolts to be tightened to their design torque
specifications. This anti-seize product assures full hydraulic efficiency by allowing the metal surfaces to slide over each
other without damaging metal-to-metal contact. Jet-Lube
™
SS-30 is also designed to work as a similar and dissimilar
component between two metal surfaces to prevent seizing and galvanic action. The SS-30 compound formula improves
conductivity and ground continuity - and will not melt in high temperatures.
Jet-Lube
™
SS-30 Pure Copper Anti-Seize Features include:
* Meets MIL-PRF-907E spec
* K-factor: 0.13
* Service rating: -65 degrees F (-54 degrees C) to 1800 degrees F (820 degrees C)
* SS-30 Resistivity (ohm-CM x 108) 5
DXE-RADP-3 - Radial Plate, Stainless Steel with 20 Sets of SS Radial Attachment Hardware
The patented DX Engineering Radial Plate is meant for those of you that have or are building a quarter wave
vertical antenna and who want an easy, neat and effective way to connect those essential radial wires and the coax
to your vertical antenna for the lowest takeoff angle and strongest signals. DX Engineering Radial Plate is laser
cut from tough stainless steel so that it has smooth edges, won’t corrode and will always look good. You will be
proud of how good your installation looks. This plate will work perfectly with most commercially available
vertical antennas such as the Hustler
®
BTV series (4-BTV thru the 6-BTV), the SteppIR™ (BiggIR or SmallIR) or
one of your own construction