- 46 -
DXE-RADW-500KBD or 1000KBD - Bulk Radial Wire Kits and Components
To achieve optimal performance with a ground-mounted vertical, install as many radials as possible. These bulk radial
wire kit use insulated wire that is UV resistant, hard to see and lays down easily, unlike the wire that is commonly
available at the big box stores. It will last much longer in contact with soil than bare wire. The biodegradable anchors
allow easy installation of radial wires, and will degrade and disappear in a year or so when they are no longer needed. The
DXE-RADW-500 or 1000KBD kits provide everything you will need to build the perfect radial system!
500/1000 ft. spool of 14 AWG, stranded copper wire with vinyl insulation
20/40 lugs
100/200 biodegradable radial wire anchor pins- Eliminating the need to bury your radials!
Build up to 20/40 radials, 25 feet long
Bulk Radial Wire Kit, 500 ft Spool of Wire, 20 Lugs, 100 Biodegradable Staples
Bulk Radial Wire Kit, 1000 ft Spool of Wire, 40 Lugs, 200 Biodegradable Staples
DXE-STPL - Radial Wire Anchor Pins, 100/pack - No need to bury your radials!
DX Engineering Radial Wire Anchor Pins are perfect for fastening radials below the grass line to eliminate the risk of damaging your
radials during lawn maintenance.
100 count - 6'' Pins
11-Gauge
Radial Wire Anchor Pins, 100/pack
Radial Wire Anchor Pins, 300/pack
DXE-STPL-100BD - Radial Wire Staple, Biodegradable, 3", 100 pack
DX Engineering DXE-STPL-100BD is a 100-pack of 3” biodegradable anchors that are produced from recycled PLA
(Polylactide Resin). Depending on the weather conditions, they will degrade in about a year. They are easily installed and
will hold radial wires in place until lawn roots overtake them - and then disappear. Ecologically friendly!
DXE-225RT-20 - Ring terminal 16-14 Wire Gauge, 1/4" hole/20-pk
\his is a set of 20 ring terminals for AWG #14 to #16 wire with a clearance hole for a 1/4" bolt. These are the same crimp
terminals supplied with the DXE Radial Wire Kits for #14 Radial and Antenna Wire.
DXE-KIT-DBR - DX Engineering Tube Deburring Tool Kit
Designed and manufactured in the USA, DX Engineering Tube Deburring Tools feature hardened steel cutting
surfaces arranged in a conical shape. Both the interior and exterior of the tool's cone may be used to smooth the rough
edges of the inside and outside of the cut ends of pipe and tubing. Its rotational symmetry allows easy reaming and
deburring rough-cut tubing edges with minimum effort. The UT-2125 is usable on all tubing and pipe sizes from 3/8”
to 2-1/8” OD. The UT-3500 covers sizes from 1-7/8” to 3-1/2” OD. The complete tool kit, model UT-KIT-DBR,
includes both sizes of conical tools, a small hand deburrer and a half round file. DX Engineering Tube Deburring
Tools are reversible, so they are ideal to deburr both ID and OD of aluminum tubing prior to telescoping the sections
together. These tools assure a smooth fit without galling and seizing that can occur with the slightest roughness. Only
a couple of revolutions with very light pressure is needed to produce excellent results. DX Engineering Tube
Deburring Tools may be used to deburr tubing and pipe made of aluminum, fiberglass, copper, steel, plastic pipe, etc.
TES-2155 - 3M Temflex™ 2155 Rubber Splicing Tape.
Conformable self-fusing rubber electrical insulating tape. It is designed for low voltage electrical insulating and moisture
sealing applications. For outdoor use, it should be protected from UV deterioration with an overwrap of TES-06132
TES-06132 - Scotch® Super 33+.
To Next Page
Loading...
