Dynascan P-72 - 9.6.- Reverse Function

To Next Page

To Previous Page

English - 30 -

CTCSS table:

Freq. (Hz)

OFF

88.5

123.0

165.5

196.6

250.3

62.5

91.5

127.3

167.9

199.5

254.1

67.0

94.8

131.8

171.3

203.5

69.3

97.4

136.5

173.8

206.5

71.9

100.0

141.3

177.3

210.7

74.4

103.5

146.2

179.9

218.1

77.0

107.2

151.4

183.5

225.7

79.7

110.9

156.7

186.2

229.1

82.5

114.8

159.8

189.9

233.6

85.4

118.8

162.2

192.8

241.8

DCS table:

DCS codes

OFF

054N/I

134N/I

225N/I

271N/I

365N/I

462N/I

612N/I

731N/I

017N/I

065N/I

143N/I

226N/I

274N/I

371N/I

464N/I

624N/I

732N/I

023N/I

071N/I

145N/I

243N/I

306N/I

411N/I

465N/I

627N/I

734N/I

025N/I

072N/I

152N/I

244N/I

311N/I

412N/I

466N/I

631N/I

743N/I

026N/I

073N/I

155N/I

245N/I

315N/I

413N/I

503N/I

632N/I

754N/I

031N/I

074N/I

156N/I

246N/I

325N/I

423N/I

506N/I

645N/I

032N/I

114N/I

162N/I

251N/I

331N/I

431N/I

516N/I

646N/I

036N/I

115N/I

165N/I

252N/I

332N/I

432N/I

523N/I

654N/I

043N/I

116N/I

172N/I

255N/I

343N/I

455N/I

526N/I

662N/I

047N/I

122N/I

174N/I

261N/I

346N/I

446N/I

532N/I

664N/I

050N/I

125N/I

205N/I

263N/I

351N/I

452N/I

546N/I

703N/I

051N/I

131N/I

212N/I

265N/I

356N/I

454N/I

565N/I

712N/I

053N/I

132N/I

223N/I

266N/I

364N/I

455N/I

606N/I

723N/I

9.6.- REVERSE FUNCTION:

If the transceiver was performed under offset working mode, you could swap the TX and RX

frequency by activate the reverse frequency function. Thus you could manually check the receiving

signal strength from other stations, while using a repeater.

1. Press and hold the [PTT/CLR] key for more than 3 seconds to select the operation band (CTRL).

2. Press the [VFO/MR] key to select the VFO mode.

3. Press the [MENU] knob, and then press the [CALL/C.IN].

● Every press the [MENU] knob and then [CALL/C.IN] key, the reverse function will be switch

between ON and OFF.

● If the reverse function is activated, “+” or “-” will show up on screen.

● If the reverse function is activated, “R” icon will show up at the right of the band.

Main Page

Dynascan P-72 - 9.6.- Reverse Function

Table of Contents

Related product manuals