E Instruments 1500 - User Manual

Other manuals for E Instruments 1500

Quick Guide2 pages

Questions and Answers

G
Guy ButlerAug 14, 2025
What to do if the sample pump is running slowly on my E Instruments 1500?
- S
  Scott HernandezAug 15, 2025
  If the sample pump in your E Instruments Measuring Instruments sounds slow, stops, or doesn't start, several issues could be the cause. First, ensure the water filter is clean and not soaked, and check the hose connected to the probe for any crushing. Next, verify the particulate filter is clean. After that, remove the rear flap and confirm the pump's electrical connector is properly connected to the printed circuit board. If these steps don't resolve the issue, the pump may be faulty and require replacement. Finally, the pump may be disabled; try switching the instrument off and then on again to re-enable it.
L
Lawrence WebbAug 18, 2025
Why are the values unreliable on the analysis screen of my E Instruments Measuring Instruments?
- M
  Misty BrennanAug 18, 2025
  If your E Instruments Measuring Instruments shows unreliable values on the analysis screen, there might be several reasons. Start by checking that the sensors are correctly installed via the sensor diagnostics menu. Then, inspect all joints and the hose for leaks in the sample probe connection. If those aren't the issue, the pump may be faulty and need replacement. As a last resort, the instrument itself might be faulty, requiring service center repair.
K
Kristi MayAug 21, 2025
What to do if the battery symbol is empty on E Instruments 1500?
- P
  plevineAug 21, 2025
  If the battery symbol on your E Instruments Measuring Instruments is empty, it means the batteries are low. To resolve this, connect the battery charger.
M
martincolinAug 25, 2025
What to do if analysis screen gives a flue gas temperature (Tf) error on E Instruments 1500 Measuring Instruments?
- J
  Jeffrey CampbellAug 25, 2025
  If your E Instruments Measuring Instruments displays a flue gas temperature error on the analysis screen, first ensure the thermocouple is properly connected to the analyzer. If the issue persists, the thermocouple may be faulty and need to be sent with the probe to a service center. The sensor might have been exposed to temperatures beyond its operating range.
M
Michael SimsAug 28, 2025
Why does the sensor diagnostics screen show an error after auto-calibration on my E Instruments 1500?
- R
  Rebecca BeltranAug 28, 2025
  If, after auto-calibration, the sensor diagnostics screen on your E Instruments Measuring Instruments displays an error for one or more sensors, it could be because the auto-calibration occurred while flue gas was being sampled. Also, the oxygen sensor might be faulty, incorrectly connected, or not connected at all. Please refer to sections 5.3, 5.4, and 6.6.
D
dgatesAug 31, 2025
What to do if a pressure sensor error is shown on E Instruments Measuring Instruments?
- A
  Anthony JonesAug 31, 2025
  If a pressure sensor error appears on the pressure/draft screen of your E Instruments Measuring Instruments, it indicates a calibration problem. The instrument should be sent to a service center.
E
eric48Sep 4, 2025
What to do if E Instruments Measuring Instruments reports a sensor error during the tightness test?
- E
  Ebony BoydSep 4, 2025
  If your E Instruments Measuring Instruments reports a sensor error during the tightness test, ensure the hose is correctly connected to the positive pressure input.
G
gordon35Sep 7, 2025
How to improve battery life of E Instruments 1500?
- J
  James BlackSep 7, 2025
  To extend the battery life of your E Instruments Measuring Instruments, store the instrument at higher temperatures. If the battery life is still unacceptable, replace the battery pack.
B
Brian JacksonSep 12, 2025
Why is the rear lighting of the display not on for E Instruments 1500 Measuring Instruments?
- D
  david97Sep 12, 2025
  If the rear lighting of the display on your E Instruments Measuring Instruments is not working, the backlighting LEDs are likely faulty. Contact the nearest service center to replace the display.