What does Fault Code 71 on my EG4 6000EX-48 Inverter mean, and how do I fix it?
Fault Code 71 on your EG4 Inverter indicates that the firmware version of each inverter is not the same. To resolve this, update all inverter firmware to the same version. Check the version of each inverter via LCD settings and ensure the CPU versions are the same.
What to do if my EG4 6000EX-48 shows Fault Code 84?
Fault Code 84 on your EG4 Inverter indicates that the AC input voltage and frequency are different. To resolve this: 1. Check the utility wiring connection and restart the inverter. 2. Ensure the utility starts up at the same time. If breakers are installed between the utility and inverters, make sure all AC input breakers can be powered on simultaneously. A main breaker or disconnect is required.
What does it mean if my EG4 6000EX-48 Inverter shows Fault Code 83 and how do I fix it?
Fault Code 83 on your EG4 Inverter means the battery voltage of each inverter is not the same. Here’s how to troubleshoot: 1. Ensure all inverters are sharing the same battery bank. 2. Remove all loads, disconnect AC input and PV input, then check the battery voltage of all inverters. If the values are close, verify all battery cables are the same length and material type.
What does Fault Code 60 mean on my EG4 6000EX-48 and how can I fix it?
Fault Code 60 on your EG4 Inverter indicates that current feedback into the inverter has been detected. To resolve this: 1. Restart the inverter. 2. Verify that the L1/L2/N cables are phased correctly in all inverters. 3. If you have a parallel system in split phase, ensure the red/black current sharing cables are securely connected to all inverters with screws.
What to do if my EG4 6000EX-48 buzzer beeps continuously and the red LED is on?
A continuous beep and red LED on your EG4 Inverter usually indicates a fault. Here's what you can check: * **Fault code 07:** Reduce the load connected to the inverter by switching off some equipment. * **Fault code 05:** Check the wiring and remove any abnormal loads. * **High Temperature:** If the internal converter component's temperature exceeds 248°F (120°C), check for blocked airflow or high ambient temperatures. * **High Battery Voltage:** Ensure the battery specifications and quantity meet the inverter's requirements. * **Fault code 01:** Replace the fan. * **Fault code 11:** Reduce solar input below 500V in all temperatures. * **Fault code 06/58:** Reduce the connected load.
How to resolve Fault Code 71 on EG4 Inverter?
If you encounter Fault Code 71 on your EG4 Inverter, it means that the firmware versions of each inverter are not the same. To resolve this: 1. Update all inverter firmware to the same version. 2. Check the version of each inverter via the LCD settings and ensure the CPU versions are the same. If not, contact your installer retailer for the firmware update. 3. If the problem persists after updating, contact your installer.
What to do if EG4 6000EX-48 relay switches on and off repeatedly?
If the internal relay of your EG4 Inverter is repeatedly switching on and off when you turn it on, it's likely that the battery is disconnected. Check if the battery wires are securely connected.
Outlines the manual's content, covering assembly, installation, operation, safety, and tools.
Details critical safety procedures, warnings, precautions for installation and operation, and specific connection advice.
Inspect the unit upon arrival to ensure it is undamaged and includes all necessary items.
Prepare for wiring by removing the bottom cover before installation.
Guidelines for selecting a location and mounting the inverter securely for optimal operation and ventilation.
Instructions for safely connecting the battery, including recommended cable sizes and torque values.
Guidelines for selecting PV modules, considering voltage ratings and environmental impacts for safe connection.
Details how the inverter operates in solar charging mode, including voltage ranges and MPP tracking.
Instructions for securing the bottom cover after all wiring is completed for safety.
Procedures for powering the unit on and off after installation is complete.
Overview of the inverter's display panel, including indicators, buttons, and LCD layout.
Connect to inverter and PC using a serial cable for monitoring software installation.
Enables wireless communication for remote monitoring and control via the SolarPower APP.
Explains parallel operation of multiple inverters for increased output power.
Details power and communication connections for two to nine inverters operating in parallel.
Connects to EG4-LL battery using RJ45 cable for communication and parameter configuration.
Details the pin definitions for the BMS communication port on the inverter.
Step-by-step guide for commissioning a single inverter system with battery, PV, or AC input.
Step-by-step guide for commissioning multiple inverters operating in parallel.
Lists warning codes, their events, and corresponding icon flashing patterns for diagnostics.
Provides a reference for fault codes, their events, and the icons displayed on the unit for troubleshooting.
Explains wireless communication using Wi-Fi module and SolarPower APP for remote monitoring and control.
Guide for downloading, installing, and setting up the SolarPower mobile application.
General| Model | EG4 6000EX-48 |
|---|---|
| Output Power | 6000W |
| Input Voltage | 48V DC |
| Waveform | Pure Sine Wave |
| Efficiency | 93% |
| Max PV Array Power | 6500W |
| Max Charging Current | 120A |
| Max AC Charging Current | 60A |
| Max PV Array Open Circuit Voltage | 500VDC |
| MPPT Voltage Range | 120-450VDC |
| Frequency | 50Hz/60Hz |
To Next Page
