EasyManua.ls Logo

EINHELL GC-DP 1340 G - User Manual

EINHELL GC-DP 1340 G
11 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GC-DP 1340 G
Art.-Nr.: 41.707.42 I.-Nr.: 11029
7
D Originalbetriebsanleitung
Schmutzwasserpumpe
GB Original operating instructions
Dirty Water Pump
F Instructions d’origine
Pompe eaux usées
I Istruzioni per l’uso originali
Pompa per acque re ue
NL Originele handleiding
Vuilwaterpomp
E Manual de instrucciones original
Bomba de agua sucia
P Manual de instruções original
Bomba de água suja
HR/ Originalne upute za uporabu
BIH Pumpa za prljavu vodu
RS Originalna uputstva za upotrebu
Pumpa za prljavu vodu
GR Πρωτότυπες Οδηγίες χρήσης
Αντλια ακαθαρτου νερου
TR Orijinal Kullanma Talimat
Pis su pompasi
Anl_GC_DP_1340_G_SPK7.indb 1 21.08.2019 15:13:53

Other manuals for EINHELL GC-DP 1340 G

Questions and Answers

  • S
    Sarah CarlsonAug 10, 2025
    Why does my EINHELL GC-DP 1340 G switch off after briefly running?
    • S
      Shawn Kelley MDAug 11, 2025
      Your EINHELL Water Pump might be switching off shortly after starting due to a couple of reasons: * The motor circuit-breaker might be tripping because of excessive water contamination. If this is the case, unplug the power and clean the equipment and shaft. * Alternatively, the water temperature may be too high, causing the motor circuit-breaker to switch off the equipment. Ensure that the water temperature does not exceed 35 °C.
  • S
    Sheila HunterAug 16, 2025
    What to do if my EINHELL GC-DP 1340 G Water Pump does not cut out?
    • M
      Michael FryeAug 16, 2025
      If your EINHELL Water Pump isn't cutting out, it might be because the floating switch can't sink. Ensure the equipment is correctly placed on the shaft bottom.
  • R
    Renee HuntAug 22, 2025
    What to do if my EINHELL Water Pump does not start?
    • A
      Amanda JonesAug 22, 2025
      If your EINHELL Water Pump doesn't start, there are a couple of things you can check: * First, make sure the power supply is properly connected. * Second, check the floating switch. If it's not triggering, raise its position.
  • E
    Emily CarsonAug 28, 2025
    What to do if my EINHELL GC-DP 1340 G does not pump water?
    • S
      Samantha LopezAug 28, 2025
      If your EINHELL Water Pump isn't pumping water, it could be due to a couple of issues: * The intake sieve might be clogged. If so, clean it with a water jet. * The discharge hose could be kinked. Straighten the hose to remove any kinks.
  • H
    haydennancySep 3, 2025
    Why EINHELL GC-DP 1340 G has insufficient pumping rate?
    • J
      James KhanSep 3, 2025
      An insufficient pumping rate in your EINHELL Water Pump can occur due to: * A clogged intake sieve. Clean the intake sieve. * Reduced performance caused by heavily contaminated and abrasive water impurities. Clean the equipment and replace any worn parts.

EINHELL GC-DP 1340 G Specifications

General IconGeneral
Power1300 W
Max Delivery Height9 m
Max Suction Depth8 m
Max Immersion Depth5 m
Mains Supply230 V
Voltage230 V
Frequency50 Hz
Max Head9 m

Related product manuals