EasyManua.ls Logo

Element RW60 - User Manual

Element RW60
116 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
RW60
User Manual

Table of Contents

Questions and Answers

  • M
    Mary AriasAug 15, 2025
    What to do if the red LED flashes and the beeper alarms on my Element RW60?
    • K
      Katrina JohnsonAug 15, 2025
      If the red LED flashes and the beeper alarms, it could be due to several reasons. First, the paper might have run out, so load the roll paper. Second, the thermal print head may be overheated; in this case, turn the printer off and resume when it cools. Third, the printer might be experiencing overvoltage, so ensure you are printing with the specified voltage. Fourth, there might be a cutter jam; try restarting the printer. Lastly, the printer cover might be open; make sure to close it.
  • J
    jennifer66Aug 17, 2025
    How to fix blurred printing or spots on my Element RW60?
    • S
      Shawn CrawfordAug 18, 2025
      Blurred printing or spots can occur for several reasons. Ensure the paper roll is loaded correctly. If that's not the issue, the paper roll might be unqualified; try using the recommended thermal paper roll. Also, the thermal head or print roller could be dirty, so clean them. Finally, the print density might be too low; increase the print density level.
  • L
    Lisa CarpenterAug 21, 2025
    What to do if my Element RW60 is not feeding paper normally?
    • D
      Daniel JacksonAug 21, 2025
      If the paper is not feeding normally, there may be a paper jam. Open the printer cover, check the paper path, and remove any jammed paper.
  • U
    umarksAug 25, 2025
    Why is my Element RW60 Printer's LED light off and the printer isn't working?
    • J
      john61Aug 25, 2025
      If the LED light is off and the printer isn't working, it could be due to a few reasons. First, the printer might not have power, so connect it to a power supply. Second, the printer might not be turned on, so turn on the printer. If neither of these solutions work, the circuit board may be broken, and you should contact the dealer.
  • T
    Timothy DouglasAug 28, 2025
    What causes vertical print words to be missing on my Element Printer?
    • K
      Kayla PerezAug 28, 2025
      Missing vertical print words can be caused by a dirty thermal head or print roller; in this case, clean them. If the problem persists, the thermal head may be damaged, and you should contact your dealer for assistance.
  • M
    Mitchell WilliamsAug 31, 2025
    Why does my Element RW60 have a coloured stripe in the paper?
    • B
      Brandon SmithAug 31, 2025
      A coloured stripe in the paper can appear if the paper is near the end of the roll. Try reloading the paper roll.
  • G
    gomezsusanSep 3, 2025
    What causes insufficient cutting on my Element RW60?
    • S
      Shannon GoldenSep 3, 2025
      Insufficient cutting can be caused by cutter edge abrasion or if the paper is too thick. In this case, replace the cutter.
  • J
    Jeffrey JohnsonSep 7, 2025
    What causes a cutter jam in Element RW60 Printer, and the movable cutter cannot go back?
    • G
      Gabrielle RossSep 7, 2025
      If the cutter is jammed and cannot return, it could be due to several reasons. The cutter might be worn from abrasion, causing insufficient cutting, so replace the cutter. The gear and wheel might be worn, so replace them. The motor could be burnt out, so replace the motor. Finally, there might be paper scraps in the transmission system, so clean them.
  • B
    Brittney NealSep 10, 2025
    Why is the purple LED always on in my Element Printer?
    • R
      Robert Hughes MDSep 10, 2025
      The purple LED being always on indicates that the roll paper is near its end. The printer can still work normally.

Element RW60 Specifications

General IconGeneral
Print Resolution203 dpi
ConnectivityUSB
Supported Media TypesLabels
Media Width25.4 mm
Media Thickness0.06 mm
MemoryRAM: 8MB, Flash: 4MB
Storage Temperature-20°C - 60°C

Related product manuals