Elmo L-12i User Manual (English)

Questions and Answers:

S
Sharon HarrisonAug 20, 2025
Why is no image displayed on my Elmo L-12i?
- L
  Lindsay BaldwinAug 20, 2025
  If no image is displayed on your Elmo Document Camera, several issues could be the cause. The AC adapter might be incorrectly connected, disconnected from the wall outlet, or disconnected from the unit's power supply socket; in any of these cases, reconnect the AC adapter. Ensure the power is ON. If you recently turned the power off and back on, wait a few seconds before turning it on again. Also, check the zoom setting, as it might be set to the TELE side, displaying only white or black. Finally, confirm that the 'RGB/HDMI/VIDEO Switch' is correctly set.
A
avilarobertAug 22, 2025
What to do if the remote control of my Elmo Document Camera does not work?
- T
  Tiffany SmithAug 22, 2025
  If the remote control for your Elmo Document Camera isn't working, first, replace the batteries with new ones. If that doesn't solve the problem, ensure you are using the remote control that was supplied with the device.
H
Holly BoltonAug 25, 2025
What to do if the image from my Elmo L-12i Document Camera is out of focus?
- C
  Christopher PalmerAug 25, 2025
  If the image from your Elmo Document Camera is out of focus, try moving the document or object slightly away from the lens. If the issue persists, manually focus the image.
V
villarrealtiffanyAug 26, 2025
What to do if the image of my Elmo L-12i is too dark?
- S
  Stacy MayAug 26, 2025
  If the image from your Elmo Document Camera is too dark, adjust the brightness by pressing the [ ] button on the operating panel or the [ ] button on the remote control.
E
Emily RussellAug 28, 2025
What to do if after inserting the SD card or USB flash drive operations cannot be performed on Elmo L-12i?
- T
  Terry GarciaAug 28, 2025
  If you cannot perform operations after inserting the SD card or USB flash drive into your Elmo Document Camera, format the card twice. First, format the card using a computer, and then format it using the main unit.
H
Henry WilsonAug 29, 2025
Why is the video output image scrambled or unclear on my Elmo L-12i Document Camera?
- H
  Harold FaulknerAug 29, 2025
  If the video output image from your Elmo Document Camera is scrambled or unclear, the video output may be set to [NTSC]. Set the video output system to PAL.
E
Eric McdonaldAug 31, 2025
How to fix striped image on Elmo Document Camera?
- B
  Bobby PageAug 31, 2025
  Striped images on your Elmo Document Camera may be due to interference fringes between dots of printed matter and TV scanning lines or CMOS pixels. Changing the shooting range may help. If you are using an LCD projector and see vertical stripes, manually adjusting the dot clock on the projector may resolve the issue.
D
Devin BatesSep 2, 2025
Why does the image not move on my Elmo L-12i?
- K
  Kenneth PetersonSep 2, 2025
  If the image on your Elmo Document Camera does not move, the camera image may be set to [Pause]. Press the Pause button on the operating panel again to restart.
G
grantjohnSep 4, 2025
What to do if the UVC image stops for a moment on Elmo L-12i Document Camera?
- J
  Justin EllisSep 4, 2025
  If the UVC image stops momentarily on your Elmo Document Camera, and the [Brightness] in the Preferences menu on the screen is set to [Auto], change the setting to [Manual].
S
sandersonSep 6, 2025
What to do if the displayed UVC image contains images other than the camera image on Elmo L-12i Document Camera?
- P
  Phillip ClarkSep 6, 2025
  If the displayed UVC image contains images other than the camera image on your Elmo Document Camera, reconnect the device or restart the software. The software, OS, or connection status may be causing this issue.