Emerson 3402 User Manual

Menu 12 Introduction
Parameter
x.00
Parameter
description format
Keypad and
display
Serial
communications
CT Modbus
RTU
PLC Ladder
programming
CTSoft Menu 0
Advanced parameter
descriptions
152 Commander SK Advanced User Guide
www.controltechniques.com Issue Number: 9
10.13 Menu 12: Programmable threshold and variable selector
Table 10-24 Menu 12 parameters: single line descriptions
Parameter Range Default Setting Update Rate
12.01 Threshold detector 1 output OFF(0) or On(1)
21 ms
12.02 Threshold detector 2 output OFF(0) or On(1)
21 ms
12.03 Threshold detector 1 source Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.04 Threshold detector 1 level 0.0 to 100.0% 0.0 21 ms
12.05 Threshold detector 1 hysteresis 0.0 to 25.0% 0.0 21 ms
12.06 Threshold detector 1 output invert OFF(0) or On(1) OFF(0) 21 ms
12.07 Threshold detector 1 destination Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.08 Variable selector 1 source 1 Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.09 Variable selector 1 source 2 Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.10 Variable selector 1 mode 0 to 9 0 21 ms
12.11 Variable selector 1 destination Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.12 Variable selector 1 output ±100.0%
21 ms
12.13 Variable selector 1 source 1 scaling ±4.000 1.000 21 ms
12.14 Variable selector 1 source 2 scaling ±4.000 1.000 21 ms
12.15 Variable selector 1 control 0.00 to 99.99 0.00 B
12.16 Not used
12.17 Not used
12.18 Not used
12.19 Not used
12.20 Not used
12.21 Not used
12.22 Not used
12.23 Threshold detector 2 source Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.24 Threshold detector 2 level 0.0 to 100.0% 0.0 21 ms
12.25 Threshold detector 2 hysteresis 0.0 to 25.0% 0.0 21 ms
12.26 Threshold detector 2 output invert OFF(0) or On(1) OFF(0) 21 ms
12.27 Threshold detector 2 destination Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.28 Variable selector 2 source 1 Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.29 Variable selector 2 source 2 Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.30 Variable selector 2 mode 0 to 9 0 21 ms
12.31 Variable selector 2 destination Pr 0.00 to Pr 21.51 Pr 0.00 Drive reset
12.32 Variable selector 2 output ±100.0%
21 ms
12.33 Variable selector 2 source 1 scaling ±4.000 1.000 21 ms
12.34 Variable selector 2 source 2 scaling ±4.000 1.000 21 ms
12.35 Variable selector 2 control 0.00 to 99.99 0.00 B
12.36 Not used
12.37 Not used
12.38 Not used
12.39 Not used
12.40 Brake release indicator OFF(0) or On(1) 21 ms
12.41 Brake controller enable {12}
diS(0), rEL(1), d IO(2),
USEr(3)
diS(0) Edit mode exit
12.42 Brake release current threshold {46} 0 to 200% 50% 21 ms
12.43 Brake apply current threshold {47} 0 to 200% 10% 21 ms
12.44 Brake release frequency {48} 0.0 to 20.0 Hz 1.0 21 ms
12.45 Brake apply frequency {49} 0.0 to 20.0 Hz 2.0 21 ms
12.46 Pre-brake release delay {50} 0.0 to 25.0 s 1.0 21 ms
12.47 Post-brake release delay {51} 0.0 to 25.0 s 1.0 21 ms
The brake control functions are provided to allow well co-ordinated operation of an external brake with the drive. While both hardware
and software are designed to high standards of quality and robustness, they are not intended for use as safety functions, i.e. where a
fault or failure would result in a risk of injury. In any application where the incorrect operation of the brake release mechanism could
result in injury, independent protection devices of proven integrity must also be incorporated.
WARNING

Emerson 3402 Specifications

General

Brand	Emerson
Model	3402
Category	Controller
Language	English