Emerson 375 - Approval Drawings

140 pages

Save Page as PDF

To Next Page

To Previous Page

Product Certifications

B-7

APPROVAL

DRAWINGS

This approval drawing can also be found on the

www.fieldcommunicator.com website.

Main Page

Default Chapter3
- Table of Contents3
- Table of Contents5
Section 49
Introduction9
Section 19
Fieldbus Functionality9
Using this Manual9
Section 211
Learning the Basics11
Overview11
Safety Messages11
Product Overview and Precautions12
- Field Communicator Components12
- Working in an Intrinsically Safe (IS) Area13
Battery and Power Supply/Charger Overview14
- Guidelines and Precautions14
- Check the Charge Remaining15
- Charge the Battery15
- Maintaining the Battery Life and Performance17
Installing the System Card and the Battery18
Removing the Battery and the System Card19
Starting up and Shutting down19
- Starting the 375 Field Communicator19
- Entering Stand-By20
- Shutting down the 375 Field Communicator20
Basic Features and Functions21
- Using the Keypad22
- Using the Touch Screen24
The 375 Main Menu25
- Starting the HART Application25
- Starting the Fieldbus Application25
- Running the Settings Menu25
- Communicating with a PC31
- Using Scratchpad34
Managing Storage37
- Types of Storage37
- Free Memory on a System Card38
Maintenance38
- Running a Self Test38
- Calibrating39
Waste Disposal39
Hazardous Substances39
HART Functionality41
Section 341
Overview41
Safety Messages41
Basic Features and Functions42
Using a Fast Key Sequence42
Starting the HART Application42
Working Offline43
- Creating New Configurations43
- Opening Saved Configurations44
Working Online48
- Connecting to a HART Loop48
- Displaying the Online Menu51
- Saving an Online Device Configuration52
- Displaying the Device Setup Submenu52
- Displaying Graphics54
Using Hot Keys55
- Setting up Hot Key Options55
- Executing a Hot Key Option56
- Removing a Hot Key Option56
- Removing All Hot Key Options56
Configuring the HART Application57
- Changing the HART Polling Option57
- Changing Ignored Status Messages59
- Changing the Menu Title59
- Storage Cleanup60
- Viewing Available Device Descriptions60
- Simulating an Online Connection to a HART Device61
Running HART Diagnostics62
- DC Voltage Measurement (HART Terminals)62
Disconnecting from a HART Device62
- Overview63
- Safety Messages63
- Basic Features and Functions64
- Link Active Scheduler (LAS)64
- Device Interoperability65
- LAS Hierarchy65
- St_Rev65
Starting the Fieldbus Application66
Working Online67
- Connecting to a Fieldbus Segment67
- Bench Hook-Up69
- Displaying the Live Device List71
- Displaying the Block List72
- Displaying a Device Menu72
- Modes73
- Working with Device Blocks76
- Displaying Graphics82
Configuring the Fieldbus Application83
- Changing the Fieldbus Polling Addresses83
- Changing the Slot Time83
- Viewing Available Device Descriptions84
Running Fieldbus Diagnostics85
- DC Voltage and Noise Level Measurement85
- Signal Level Measurement85
Disconnecting from Afieldbus Device86
Section 587
Troubleshooting Suggestions87
Overview87
Error and Status Messages92
Required Information for Technical Assistance96
APPENDIX A Reference Information97
Processor and Memory Specifications97
- Microprocessor97
- Memory97
Power Supply/Charger Specifications98
Physical Specifications98
Connection Specifications98
Battery Specifications100
Temperature Specifications100
Order Information101
Spare Parts List103
Product Certifications105
Appendix B105
Overview105
Approved Manufacturing Locations105
European Directive Information105
Hazardous Locations Certifications (KL Option Only)106
- International Certifications106
- North American Certifications106
- European Certifications107
Power Supply/Charger Certification108
Label Drawings108
Approval Drawings111
APPENDIX C Graphics Information115
Overview115
Screen Layout116
Buttons117
Graphics Options118
- Images118
- Charts119
- Gauge Charts123
- Graphs124
Glossary125
Index133

Emerson 375 - Approval Drawings

Table of Contents

Related product manuals