Emerson Digitax ST User Manual

Safety
Information
Product
information
Mechanical
installation
Electrical
installation
Getting
started
Basic
parameters
Running the
motor
Optimization
EtherCAT
interface
SMARTCARD
Operation
Onboard
PLC
Advanced
parameters
Technical
Data
Diagnostics
UL listing
information
112 Digitax ST User Guide
Issue Number: 5
Low voltage supply 6.44 6.46
Marker pulse 3.32 3.31
Maximum speed 1.06
Menu 0 set up 11.01 to 11.22 Menu 22
Minimum speed 1.07 10.04
Motor map 5.07 5.08 5.09 5.11
Motor map 2 Menu 21 11.45
Motorized potentiometer 9.21 9.22 9.23 9.24 9.25 9.26 9.27 9.28
Offset speed reference 1.04 1.38 1.09
Onboard PLC 11.47 to 11.51
Open collector digital outputs 8.30
Orientation 13.10 13.13 to 13.15
Output 5.01 5.02 5.03 5.04
Overspeed threshold 3.08
Phase angle 3.25 5.12
PID controller Menu 14
Position feedback - drive 3.28 3.29 3.30 3.50
Positive logic 8.29
Power up parameter 11.22 11.21
Precision reference 1.18 1.19 1.20 1.44
Preset speeds 1.15 1.21 to 1.28 1.16 1.14 1.42 1.45 to 1.48 1.50
Programmable logic Menu 9
Ramp (accel / decel) mode 2.04 2.08 6.01 2.02 2.03 10.30 10.31 10.39
Rated speed autotune 5.08
Regenerating 10.10 10.11 10.30 10.31 6.01 2.04 2.02 10.12 10.39 10.40
Relative jog 13.17 to 13.19
Relay output 8.07 8.17 8.27
Reset 10.33 8.02 8.22 10.34 10.35 10.36 10.01
S ramp 2.06 2.07
Safe Torque Off input 8.09 8.10
Sample rates 5.18
Security code 11.30 11.44
Serial comms 11.23 to 11.26
Skip speeds 1.29 1.30 1.31 1.32 1.33 1.34 1.35
SMARTCARD 11.36 to 11.40 11.42
Software version 11.29 11.34
Speed controller 3.10 to 3.17 3.19 3.20 3.21
Speed feedback 3.02 3.03 3.04
Speed feedback - drive 3.26 3.27 3.28 3.29 3.30 3.31 3.42
Speed reference selection 1.14 1.15 1.49 1.50 1.01
Status word 10.40
Supply 6.44 5.05 6.46
Switching frequency 5.18 5.35 7.34 7.35
Thermal protection - drive 5.18 5.35 7.04 7.05 7.06 7.32 7.35 10.18
Thermal protection - motor 4.15 5.07 4.19 4.16 4.25 7.15
Thermistor input 7.15 7.03 10.37
Threshold detector 1 12.01 12.03 to 12.07
Threshold detector 2 12.02 12.23 to 12.27
Time - filter change 6.19 6.18
Time - powered up log 6.20 6.21 6.28
Time - run log 6.22 6.23 6.28
Torque 4.03 5.32
Torque mode 4.08 4.11 4.09 4.10
Trip detection 10.37 10.38 10.20 to 10.29
Trip log 10.20 to 10.29 10.41 to 10.51 6.28
Under voltage 5.05 10.16 10.15
Variable selector 1 12.08 to 12.15
Variable selector 2 12.28 to 12.35
Velocity feed forward 1.39 1.40
Voltage controller 5.31
Voltage mode 5.14 5.17
Voltage rating 11.33 5.09 5.05
Voltage supply 6.44 6.46 5.05
Warning 10.19 10.12 10.17 10.18 10.40
Zero speed indicator bit 3.05 10.03
Feature Parameter number (Pr)

Emerson Digitax ST Specifications

General

Brand	Emerson
Model	Digitax ST
Category	Controller
Language	English