Why CDI communication is not working on Endress+Hauser Radar?
If CDI communication does not work with your Endress+Hauser Radar, the COM port setting on your computer may be incorrect. Check the COM port setting and change it if necessary.
What to do if HART communication does not function on Endress+Hauser Levelflex FMP51?
If HART communication isn't working on your Endress+Hauser Measuring Instruments: * A communication resistor might be missing or installed incorrectly. Install the communication resistor (250 ?) correctly. * The Commubox could be connected incorrectly. Connect the Commubox correctly. * The Commubox might not be switched to HART mode. Set the selection switch of the Commubox to the HART position.
How to troubleshoot an Endress+Hauser Radar device that does not respond?
If the Endress+Hauser Radar device does not respond, it could be due to the following reasons: * The supply voltage is not connected. Connect the correct voltage. * The cables do not contact the terminals properly. Ensure electrical contact between the cable and the terminal.
What to do if there is no change of the measured value when emptying/filling the Endress+Hauser Measuring Instruments tank?
If the measured value doesn't change when emptying or filling the tank with your Endress+Hauser Measuring Instruments: * An interference echo may be affecting the measurement. Perform mapping. * There might be build-up on the probe. Clean the probe. * There could be an error in the echo tracking. Deactivate echo tracking.
What to do if the values on my Endress+Hauser Measuring Instruments display are invisible?
If the values on your Endress+Hauser Measuring Instruments display are not visible: * The contrast setting may be too weak or too strong. Increase contrast by pressing the indicated buttons simultaneously or decrease contrast by pressing the indicated buttons simultaneously. * The plug of the display cable might not be connected correctly. Connect the plug correctly. * The display itself could be defective. Replace the display.
Why does my Endress+Hauser Levelflex FMP51 Measuring Instruments device measure incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, it could be due to a parameterization error. Check and adjust the parameterization.
What to do if with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in Endress+Hauser Measuring Instruments?
If, with the setting Tank level = Partially filled, the measured total level jumps to lower values during filling operations in your Endress+Hauser Measuring Instruments, the total level might be running into the upper blocking distance. Decrease the blocking distance.
What to do if values on Endress+Hauser Radar display are invisible?
If the values on your Endress+Hauser Radar's display are invisible, here are a few things to check: * The contrast setting might be too weak or too strong. Try increasing the contrast by pressing the indicated buttons simultaneously or decreasing it in the same way. * The display cable plug might not be connected correctly; ensure it is properly connected. * The display itself might be defective, in which case you should replace it.
What to do if Endress+Hauser Radar device measures incorrectly?
If your Endress+Hauser Radar device is providing incorrect measurements, the cause could be a parameterization error. To solve this, check and adjust the parameterization of the device.
Why Endress+Hauser Radar device does not respond?
If your Endress+Hauser Radar device isn't responding, it could be due to a couple of reasons: * The supply voltage might not be correctly connected; ensure you connect the correct voltage. * The cables might not be making proper contact with the terminals; make sure there's good electrical contact between the cable and the terminal.
Explains the purpose of the operating instructions and defines safety, electrical, tool, and graphic symbols.
Lists related documents like Technical Information, Brief Operating Instructions, and parameter descriptions.
Outlines requirements for personnel, designated applications, and workplace safety protocols.
Covers operational safety, unauthorized modifications, repairs, and product safety certifications (CE, EAC).
Details the Levelflex FMP51/FMP52/FMP54/FMP55 design, including housing and probe types.
Lists registered trademarks used in the document, such as FOUNDATION Fieldbus and VITON.
Details steps for checking delivery notes, goods condition, and nameplate data.
Explains how to identify the measuring device using nameplate, order code, W@M Device Viewer, or Operations App.
Specifies the permitted storage temperature range and the use of original packaging.
Provides guidelines for safe transport, including handling warnings and fastening points.
Details mounting distances, suitable positions, and additional conditions for proper installation.
Explains how to mount the device using threaded connections or flanges, including torque specifications.
Describes the installation of devices with a remote sensor, including cable connection and bending radius.
Lists checks to perform after installation to ensure the device is undamaged and correctly installed.
Details terminal assignments for FOUNDATION Fieldbus, including overvoltage protection options.
Covers cable specifications, plug connectors (M12, 7/8"), and connection examples.
Explains power supply requirements for FOUNDATION Fieldbus and details integrated/external overvoltage protection.
Describes local operation using pushbuttons or touch control and its additional functionalities.
Explains remote operation via FOUNDATION Fieldbus system architecture and service interface (CDI).
Details the operating menu structure, user roles, access authorization, and write protection.
Covers display appearance, symbols, status signals, locking states, and operating elements.
Information on DD files, integration steps, and device identification/addressing in FF networks.
Explains the device's block structure, including Resource, Transducer, and Function Blocks.
Lists parameters for Setup, Advanced Setup, Display, Diagnostic, Expert, and Service Transducer Blocks.
Describes methods like Restart, Setup, Linearization, and Self Check for device operation.
Guides users through initial setup using FieldCare or DeviceCare wizards.
Details steps for installation checks, language settings, reference distance, and measurement configuration.
Provides steps for configuring interface measurements, including tank level and DC value.
Covers saving/restoring configurations, managing events, and transmitting data.
Addresses general errors like device response issues and parametrization errors for level/interface measurements.
Explains how diagnostic messages, status signals, and event texts are displayed and interpreted.
Covers viewing event history, filtering events by category, and understanding information events.
Provides instructions for cleaning the device exterior using appropriate cleaning agents.
Covers repair concepts, spare parts, and specific procedures for Ex-approved devices.
Details the process for replacing electronics modules or the entire device and parameter download.
Lists accessories like weather protection covers, mounting brackets, and extension rods.
Details accessories for communication, such as Commubox FXA291 and Field Xpert devices.
Mentions system components like the Graphic Data Manager Memograph M for data management.
Provides a structured overview of the operating menu accessible via the device's display module.
Maps out the operating menu structure accessible via external operating tools like FieldCare.
Details parameters within the Setup menu, including operating mode, tank type, and calibration.
Covers parameters for diagnostics like actual, previous, and event logbook information.
Explains the Heartbeat submenu for device diagnostics and monitoring application packages.
General| Device Type | Guided radar level transmitter |
|---|---|
| Application | Level measurement for liquids and solids |
| Measuring Range | Up to 30 m |
| Process Temperature | -40 to 200 °C (-40 to 392 °F) |
| Process Pressure | -1 to +40 bar (-14.5 to +580 psi) |
| Output Signal | 4-20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Housing Material | Aluminum, Stainless steel |
| Probe Type | Rod or cable |
| Material | Stainless steel, PTFE |
| Protection Rating | IP66/IP67 |
| Approvals | ATEX, IECEx, FM, CSA |
| Power Supply | 10.5 to 36 V DC |
To Next Page