envea STACK 710 User Manual

Name: envea STACK 710
Brand: envea
Rating: 5 (1 reviews)

68 pages

To Next Page

To Previous Page

3 Installation Instructions STACK 710

22 (PC-000878-MA Issue 7, December 2021) ENVEA UK Ltd

3.10 Transceiver Connections

Figure 10: Transceiver connections.

Table of Contents5
List of Figures6
Introduction9
Purpose of this Manual9
Limits of Use11
Additional Information11
Certification12
Product Description13
Figure 1: STACK 710- General Overview13
Installation Diagram14
Figure 2: STACK 710- Installation Diagram14
Installation Instructions15
Installation Checklist15
Selecting an Installation Location15
Maintaining the Pathlength During Installation16
Figure 3: STACK 710- Installation Schematic16
Installing the Mounting Flanges17
Figure 4: STACK 710- Pathlength Distance17
Figure 5 Mounting Flange Schematic17
Mounting Details18
Flange Alignment Tool18
Figure 6: Front View of Air Purge Showing Mounting Holes18
Important Information for Installing the Transceiver and Retro-Reflector19
Figure 7: Installing the Transceiver and Retro-Reflector (Side View)19
Figure 8: Installing the Transceiver and Retro-Reflector (Top View)19
Mounting the Transceiver and Retro-Reflector20
Figure 9: Mounting the Transceiver and Retro-Reflector20
Electrical Connections21
3.10 Transceiver Connections22
Figure 10: Transceiver Connections22
3.11 Connection to ENVEA Control Unit23
Figure 11: SPUR Unit Connections23
3.12 Cable Specification25
Figure 12: Electrical Connection Overview25
PC Software (PC-ME DUST TOOLS)26
Getting Started27
User Interface27
Figure 13: User Interface27
Function Keys28
STACK 710 Symbols29
Glossary of Terms30
Using the Instrument for the First Time31
Align the Retro-Reflector32
Figure 14: Opening the Retro-Reflector Case & Releasing the Reflector32
Align the Transceiver33
Figure 15: Aligning the Retro-Reflector33
Setup Calibration Check Interval34
Setup Current Loop Output34
4.10 Setup Alarm36
4.11 Calibration Check36
4.12 Modbus Interface36
4.13 Modbus Registers38
Periodic Mode of Operation40
Calibration Check40
Figure 16: STACK 710- Transceiver40
Calibration Audit41
Clear Stack Calibration42
Gravimetric Calibration (Isokinetic Calibration)43
Setting Calibration Constants Manually45
Theory of Operation and Application48
General Outline48
Beer-Lambert's Law48
Figure 17: Beer-Lambert's Law48
Pathlength Correction Factor (PLCF)50
Figure 18: Double Pass System50
Examples of Different Pathlength Correction Factors (PLCF)52
Figure 19: Examples of Different Pathlength Correction Factors (PLCF)52
Requirements for Environmental Legislation53
Figure 20: STACK 710- Overview53
Figure 21: STACK 710- Transceiver54
System Specification55
Maintenance57
Identifying Faults57
Fault Number List58
Maintenance59
Cleaning the Optical Surfaces60
Transceiver Cover60
Figure 22: STACK 710- Removing the Cover60
Configuration Record Sheet61
Envea Service and Support Centres68

Questions and Answers:

Need help?

Do you have a question about the envea STACK 710 and is the answer not in the manual?

envea STACK 710 Specifications

General

Brand	envea
Model	STACK 710
Category	Measuring Instruments
Language	English

envea STACK 710 User Manual

Table of Contents

Questions and Answers:

envea STACK 710 Specifications