Epilog Laser FusionPro 16000 - Page 56

242 pages

To Next Page

To Previous Page

To use the Material Settings that are automatically loaded in your Job Manager, go to the Jobs tab and

double-click on the job you want to process.

Click the Import Material Settings icon.

- 50 -

SECTION 4: THE JOB MANAGER

Main Page

Default Chapter3
- Table of Contents3
Fire Warning7
Introduction8
- How to Use this Owner's Manual8
- Icons Used in this Manual8
Section 1: Safety9
- Laser Safety9
- Electrical Safety10
- Safety Features and Regulatory Compliance11
- Do and Don't17
Section 2: Getting Started19
- 1 Unpacking the Laser System20
- 2 Choose Where to Locate the System22
- 3 Connecting the Exhaust23
- 4 Connecting Electrical Power25
- 5 Connect the Laser to Your Computer25
- 6 Set the Fusion Pro's IP Address26
- 7 Sign up for Driver Updates and Register Your System27
Section 3: Software Installation29
- Epilog Job Manager Instructions29
- Uninstalling the Previous Job Manager29
- How to Install the Epilog Software Suite31
- Windows 8/10: Ethernet Installation37
- Windows 8/10: USB Installation39
- Troubleshooting the Job Manager39
- Important Job Manager Notes40
Section 4: the Job Manager41
- Using the Epilog Job Manager41
- Printing to the Epilog Job Manager42
- Organizing Your Print Jobs43
- Previewing Your Job46
- Searching for a Job47
- Finding Job History47
- Vector Sorting49
- Material Settings Tab50
- Job Settings Tab53
- Using the Material Setting Configurations55
- Changing Program Settings57
- Troubleshooting the Job Manager58
Section 5: the Laser Dashboard61
- Setting up Coreldraw for the Laser62
- Sending Your First Project63
- Setting up Adobe Illustrator for the Laser67
- Dashboard Settings69
- Presetting Your Cut Lines71
- Placing Your Artwork71
- Dividing Your Job into Processes72
- Editing Artwork with Live View81
- Saving Your Settings84
- File Settings85
- Settings in Detail86
- Guidelines88
- Processes Tab91
- Advanced Tab92
- Notes Tab92
- Additional Coreldraw Laser Dashboard Features93
- File Setup Faqs94
- Troubleshooting the Laser Dashboard94
Section 6: Control Panel99
- Display99
- Joystick107
- Job Storage107
Section 7: Quick Start Guide109
- Artwork Setup109
- Setting a Vector Cutting Line111
- Resolution111
- Landscape or Portrait113
Section 8: System Features115
- IRIS TM Camera Positioning System115
- Touch Screen115
- Air Assist116
- Auto Focus Vs Manual Focus116
- Key Switch118
- Image Dithering118
- Red Dot Pointer120
- Emergency Stop Button120
- Front Access Door120
- Task Plate/Vacuum Hold-Down Table121
- Exhaust Plenum121
- Center Engraving122
- Registration Camera125
Section 9: Optional Features133
- Vector Cutting Table/Slat Table133
- Fusion Pro Rim-Drive Rotary Attachment134
- 3-Jaw Chuck Rotary Attachment140
- Photolaser Plus154
Section 10: System Maintenance163
- Reduce Fire Risk with a Clean Laser163
- Cleaning the Optics165
- Replacing the Lens170
- Cleaning the Exhaust Plenum171
- Laser Tube171
- Removing the Pedestal from the Fusion Pro172
Section 11: Upgrading Firmware179
- How to Upgrade Your Firmware179
Section 12: Engraving Materials185
- CO2 Laser Materials/Techniques185
- Fiber Laser Materials/Techniques199
Section 13: Specifications203
- Fusion Pro Laser Technical Specifications203
- Compatibility204
- Recommended PC204
- About the CO2 Laser Source205
- About the Fiber Laser Source206
- Federal Communications Commission (FCC) Notice206
Section 14: Technical Support207
- Contacting Technical Support207
- Frequently Asked Questions208
- Join Epilog Laser's Online Community210
Section 15: Material Suppliers211
- Industry Material Supplier List211
Appendix A: Warranty Statement215
- Warranty Statement for the Fusion Pro Laser215
Appendix B: Material Settings217
- Fusion Pro Suggested Material Settings (CO2)217
- Fusion Pro Suggested Material Settings (Fiber)220
Appendix C: System Calibration223
- Camera Calibration223
- Calibrating the Auto Focus227
Index237

Epilog Laser FusionPro 16000 - Page 56

Table of Contents

Related product manuals