Epson EB-L260F User Manual

274
Solutions to Remote Control Problems
If the projector does not respond to remote control commands, try the following solutions:
• Check that the remote control batteries are installed correctly and have power. If necessary, replace
the batteries.
• Make sure you are operating the remote control within the reception angle and range of the projector.
• Make sure the projector is not warming up or shutting down.
• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release
the button to wake the remote control up.
• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the
projector's remote receivers. Dim the lights or move the projector away from the sun or interfering
equipment.
• If available, turn on one of the remote receivers in the projector's menu system, or check if all the
remote receivers were turned off.
• If the remote receiver setting is off, press and hold the Menu button on the remote for at least 15
seconds to restore the default setting.
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to
check or change the ID setting.
• To set the remote control so it will operate any projector, hold down the ID button and press the 0/All
button.
• If you lose the remote control, you can purchase another from an Epson parts distributor.
Parent topic: Solving Projector or Remote Control Operation Problems
Related references
Remote Control Operation
Related tasks
Installing Batteries in the Remote Control
Replacing the Remote Control Batteries
Solutions to Password Problems
If you cannot enter or remember a password, try the following solutions:
• You may have turned on password protection without first setting a password. Try entering 0000 using
the remote control. If you lose the remote control, you cannot enter a password. Order a new one from
Epson.

Epson EB-L260F Specifications

General

Heat dissipation	884 BTU/h
Number of colors	1.07 billion colors
Native aspect ratio	16:9
Vertical scan range	192 - 240 Hz
Projection technology	3LCD
Contrast ratio (typical)	2500000:1
Screen size compatibility	31 - 310 \
Projection distance (wide)	0.9 - 9.1 m
Projector native resolution	1080p (1920x1080)
Keystone correction, horizontal	30 °
Projector brightness (economic mode)	3200 ANSI lumens
Light source type	Laser
Service life of light source	20000 h
Service life of light source (economic mode)	30000 h
Offset	1000 %
Throw ratio	1.32 - 2.12:1
Zoom capability	Yes
Focal length range	18.2 - 29.1 mm
Aperture range (F-F)	1.51 - 1.77
Serial interface type	RS-232C
USB 2.0 ports quantity	2
VGA (D-Sub) ports quantity	3
USB 2.0 Type-A ports quantity	1
Wi-Fi standards	Wi-Fi 5 (802.11ac)
Noise level	37 dB
Projection modes	Ceiling, Front
Noise level (economic mode)	27 dB
Placement	Ceiling, Desktop, Floor, Wall
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
Video color modes	Blackboard, DICOM simulation mode, Dynamic, Multi-projection, Presentation, sRGB
RMS rated power	16 W
Power source	AC
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	260 W
Power consumption (standby)	0.5 W
Power consumption (typical)	199 W
Power consumption (economy mode)	144 W
Storage temperature (T-T)	-10 - 60 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Cables included	HDMI, Power
Bundled software	Epson Creative Projection, EasyMP Multi PC Projection, Epson Projector Content Manager, Epson Projector Management
Quantity per pack	1 pc(s)

Weight and Dimensions

Depth	299 mm
Width	325 mm
Height	90 mm
Weight	4200 g