Epson EB-X9 User Manual

Check Remedy
Are the "
Sync. g " and "Tracking g " settings adjusted correctly?
Only when projecting computer images
Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
adjustment. If the images are not adjusted correctly after using automatic adjustment, you can make the adjustments
using Sync. and Tracking from the Configuration Menu.
s
Signal Menu - Tracking, Sync. p.50
The image is truncated (large) or small, or the aspect ratio is not suitable
Check Remedy
Is a wide panel computer image being projected?
Only when projecting computer images
Change the setting according to the signal for the connected equipment. s Signal Menu - Resolution p.50
Is the image still being enlarged by E-Zoom? Press the [Esc] button on the Remote Control to cancel E-Zoom. s p.33
Is Position adjusted correctly? Press the [Auto] button on the Remote Control or the [Enter] button on the Control panel to perform automatic
adjustment of the computer image being projected. If the images are not adjusted correctly after using automatic
adjustment, you can make the adjustments using Position from the Configuration Menu.
Apart from computer image signals, you can adjust other signals while projecting by adjusting Position from the
Configuration Menu. s Signal Menu - Position p.50
Is the computer set for dual display?
Only when projecting computer images
If dual display is activated in the "Display Properties" of the computer's Control Panel, only about half of the image on the
computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting. s
Computer video driver documentation
Is the correct resolution selected?
Only when projecting computer images
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.90 s Computer documentation
Image colors are not right
Check Remedy
Do the input signal settings match the signals from the connected
device?
Change the following settings according to the signal for the connected equipment.
When the image is from a device connected to the Computer input port s Signal menu - Input Signal p.50
When image is from a device connected to the Video or S-Video input port s Signal menu - Video Signal p.50
Is the image Brightness adjusted correctly? Adjust the Brightness setting from the Configuration Menu. s Image menu - Brightness p.49
Are the cables connected correctly? Check that all the cables required for projection are securely connected. s Quick Start Guide
Is
Contrast g adjusted correctly? Adjust the Contrast setting from the Configuration Menu. s Image Menu - Contrast p.49
Problem Solving
66

Epson EB-X9 Specifications

General

Matrix size	0.55 \
Projection distance	1.8 - 2.4 m
Projection technology	LCD
Contrast ratio (typical)	2000:1
Screen size compatibility	30 - 300 \
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	30 °
Audio input	1 x RCA
Aspect ratio	4:3
RS-232 ports	0
Dimensions (WxDxH)	295 x 228 x 77 mm
Lamp type	UHE
Lamp power	200 W
Light source type	Lamp
Service life of light source	4000 h
Service life of light source (economic mode)	5000 h
Analog signal format system	-
RMS rated power	1 W
Number of built-in speakers	1
DVI port	No
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (standby)	0.4 W
Power consumption (typical)	265 W
Noise level	37 dB
Country of origin	China
Pallet width	800 mm
Pallet height	2230 mm
Pallet length	1200 mm
Pallet width (UK)	1000 mm
Quantity per pack	1 pc(s)
Quantity per pallet	78 pc(s)
Quantity per pallet layer	6 pc(s)

Weight and Dimensions

Weight	2300 g
Package depth	360 mm
Package width	340 mm
Package height	160 mm
Package weight	4060 g