Epson L655 - Page 35

ConfidentialConfidential
Dis
Disaasssseemmbbllyy//ReReaasssseemmbbllyy CoCommmmoon cn caauuttioionns s wwhheen dn disisaasssseemmbbllining/g/rereaasssseemmbbllining tg thhe e ProProdduucctt 3355
p gp g
MMoottoorrss TTaakke e ccaarre e nnoot t tto o ddaammaagge e tthheemm..
------
SeSennsosorrss 1.1. TaTake ke ccaare re nnoot t to to totouucch h ththe e ddeteteecctotor r sseectctioionns.s.
2.2. As for thAs for the encode encoder Sensor er Sensor used with used with a circular a circular scale, the scale, the photo senphoto sensorsor
section should be set over the encoded area of the circular scale.section should be set over the encoded area of the circular scale.
3.3. Take care Take care not to gnot to get injured et injured by the by the sharp ensharp ends of thds of the board e board terminal oterminal onn
the back of the circuit boards when handling the sensors or thethe back of the circuit boards when handling the sensors or the
peripheraperipheral parts.l parts.
SSccaalleess 11.. TTaakke e ccaarre e nnoot t tto o ttoouucch h tthhe e eennccooddeed d aarreeaa..
2.2. Install it Install it with the with the black trblack triangular iangular section section up. (CR up. (CR Scale oScale only)nly)
3.3. Wipe oWipe off alcff alcohoohol befol before instre installinalling. (CR Scg. (CR Scale onale only)ly)
4.4. Confirm Confirm that thethat they do y do not tounot touch the ch the photo sphoto sensors ensors after inafter installation.stallation.
Waste inkWaste ink
padspads
1.1. Take carTake care not to e not to stain youstain your hands r hands with the with the waste ink waste ink soaked soaked in the inin the inkk
pads. If ink pads. If ink comes intcomes into contact wio contact with your hath your hands, wash nds, wash it off with wateit off with waterr
immediately.immediately.
2.2. Take carTake care not to e not to stain the stain the printer's paprinter's parts with thrts with the waste e waste ink soakink soaked in thed in thee
ink pads. If ink comes into contact with the parts, wash it off.ink pads. If ink comes into contact with the parts, wash it off.
(Especially, pay attention to Paper Guide Front/Lower Porous Pad)(Especially, pay attention to Paper Guide Front/Lower Porous Pad)
3.3.
2.2.
4.4.
2.2.
2.2.

E
E ppssoon n EE TT--44555500, , LL665555//665566 RReevviissiioon n BB
FFFFCsCs 11.. BBe se suure re to to ininsesert rt ththem em to to ththeeir ir ccoonnnnecectotorrs os on tn thhe be booaardrds as as fs faar ar as ts thheeyy
will go without any loose connection such as a half-way or slantwill go without any loose connection such as a half-way or slant
connection.connection.
2.2. RoutRoute thee them alom along thng their reir routiouting png pathsaths..
3.3. If the doIf the double-sideuble-sided tape d tape that secuthat secures the FFres the FFCs is not Cs is not strong estrong enough nough toto
secure them, make sure to replace the tape and secure the FFCs firmly.secure them, make sure to replace the tape and secure the FFCs firmly.
------
GGeeaarsrs WhWheen n ininsstatallllining g ggeeaarsrs, , ppaay y atattetennttioion n to to ththe e ffoolllloowwiningg::
•• The geThe gear sectioar section shoun should not ld not be dabe damaged.maged.
•• No foNo foreigreign matn materiaerial is attl is attacheached.d.
•• No grease No grease is attached is attached on any paon any parts other thrts other than those span those specified.ecified.
------
PF rPF rolollelersrs Do nDo not tot tououch rch rolollelers frs for por papaper fer feeeediding wng whehen han handndliling tng thehem.m.
One TimeOne Time
partsparts
After removing One Time parts specified in this manual, do not reuseAfter removing One Time parts specified in this manual, do not reuse
them, but be sure to replace them with new ones.them, but be sure to replace them with new ones.
One Time icon:One Time icon:
ADF/ScannerADF/Scanner
UnitUnit
When disassembling/reassembling the ADF/Scanner Unit, make sure toWhen disassembling/reassembling the ADF/Scanner Unit, make sure to
do the work with the unit open to prevent damage to the Hinges.do the work with the unit open to prevent damage to the Hinges.
Holder CamHolder Cam
AssyAssy
Install the assy while aligning the protrusion on the D/E Lever with theInstall the assy while aligning the protrusion on the D/E Lever with the
groove on the cam of the Holder Cam Assy.groove on the cam of the Holder Cam Assy.
I
Itteemm CCoonntteenntt PPhhoottoo//IIlllluussttrraattiioonn
Holder Cam AssyHolder Cam AssyD/E LeverD/E Lever
PPrroottrruussiioonn GGrroooovvee