
E
E ppssoon n EETT--44555500, , LL665555//665566 RReevviissiioonn BB
DDiissaasssseemmbbllyy//RR eeaasssseemmbbllyy DDeettaaiilleed d DDiissaasssseemmbbllyy//RReeaasssseemmbblly y PPrroocceedduurre e ffoor r eeaacch h PPaarrtt//UUnniitt 4466
Confidentialî˜ Confidentialî˜
Scanner Housing Lower Assy
Scanner Housing Lower Assy
Install the Scanner driver gears, scanner drive lever, and Extension Spring 0.526 as shown above.Install the Scanner driver gears, scanner drive lever, and Extension Spring 0.526 as shown above.
ScannerS drive gearsScannerS drive gears
Extension Spring 0.526Extension Spring 0.526
Scanner drive leverScanner drive leverScanner Housing Lower AssyScanner Housing Lower Assy
Panel Unit
Panel Unit
Remove the Panel Unit as follows.Remove the Panel Unit as follows.
1.1. Remove tRemove the screwhe screws (x 2) ts (x 2) that securhat secure the Pane the Panel Unit.el Unit.
2.2. Release thRelease the hooks (x 3) oe hooks (x 3) on the Panel Unn the Panel Unit, and detacit, and detach the Panel Unh the Panel Unit.it.
3.3. DisconnDisconnect the Panel FFC and the Speaker cable from the conneect the Panel FFC and the Speaker cable from the connectors on the backface of the Panel Boardctors on the backface of the Panel Board, and remove the Panel Unit., and remove the Panel Unit.
Panel Unit (Backface)Panel Unit (Backface)
Panel UnitPanel Unit
C.B.P-TITE SCREW 3x10 F/ZB-3C (6 ± 1C.B.P-TITE SCREW 3x10 F/ZB-3C (6 ± 1
î™—î™—
kgfî™’kgfî™’
··
cm)cm)
Hookî™’Hookî™’
Step3Step3
PPaanneel Bl Booaarrdd SSppeeaakkeer cr caabbllee
Panel FFCPanel FFC
Panel Board
Panel Board
 When reassembling, align the dowels on the Panel HousingWhen reassembling, align the dowels on the Panel Housing
Assy with the positioning holes on the Panel Board.Assy with the positioning holes on the Panel Board.

Tighten the screws in the order indicated in the figure above.Tighten the screws in the order indicated in the figure above.
C.B.P-TITE SCREW 3x10 F/ZN-3C (6C.B.P-TITE SCREW 3x10 F/ZN-3C (6
±±
î™’1kgfî™’î™’1kgfî™’
··
cm)cm)
Dowel and positioning holeDowel and positioning hole
PPaanneel l HHoouussiinng g AAssssyy PPaanneel l BBooaarrdd
11
22
33
44
Speaker
Speaker
When handling the Speaker, do not pinch the middle of the wooferWhen handling the Speaker, do not pinch the middle of the woofer
cone but make sure to hold it by the rim.cone but make sure to hold it by the rim.
SpeakerSpeaker
OKî™’OKî™’
NGNG
SpeakerSpeaker
Housing Upper
Housing Upper
Since the Housing Upper is secured by the hooks (x 2) shown above, release the hooks with a precision screwdriver or a similar tool when removingSince the Housing Upper is secured by the hooks (x 2) shown above, release the hooks with a precision screwdriver or a similar tool when removing
the Housing Upper.the Housing Upper.
Housing UpperHousing Upper
LeftLeft
Hookî™’Hookî™’
Precision driverPrecision driver
RightRight
Precision driverPrecision driver
Hookî™’Hookî™’
To Next Page
Loading...
