ESAB Cutmaster 120 - Page 45

ESAB CUTMASTER 120
Manual 0-5380 OPERATION
4T-19
Type Torch: SL100 With Shielded Tip Type Material: Stainless Steel
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage Speed (Per Minute) Standoff Plasma Gas Press Flow (CFH) Pierce Pierce Height
Inches mm (Cat. No.) Volts(VDC) (Amps) Inches Meters Inches mm psi* bar Plasma Total** Delay (Sec) Inches mm
0.250
6.4 9-8253
136 120 180
4.57
0.13
3.2
75
5.2 180 360
0.20 0.20
5.1
0.375
9.5 9-8253
144 120 100
2.54
0.13
3.2
75
5.2 180 360
0.40 0.20
5.1
0.500
12.7 9-8253
149 120 60
1.52
0.13
3.2
75
5.2 180 360
0.80 0.20
5.1
0.625
15.9 9-8253
153 120 40
1.02
0.15
3.8
75
5.2 180 360
1.20 0.20
5.1
0.750
19.1 9-8253
157 120 30
0.76
0.15
3.8
75
5.2 180 360
NR NR
NR
1.000
25.4 9-8253
162 120 20
0.51
0.15
3.8
75
5.2 180 360
NR NR
NR
1.250
31.8 9-8253
165 120 10
0.25
0.15
3.8
75
5.2 180 360
NR NR
NR
Type Torch: SL100 With Shielded Tip
Type Material: Aluminum
Type Plasma Gas: Air Type Secondary Gas: Single Gas Torch
Thickness Tip Output Amperage Speed (Per Minute) Standoff Plasma Gas Press Flow (CFH) Pierce Pierce Height
Inches mm (Cat. No.) Volts(VDC) (Amps) Inches Meters Inches mm psi* bar Plasma Total** Delay (Sec) Inches mm
0.250
6.4 9-8253
144
120
190
4.83
0.13
3.2
75
5.2 180 360
0.20 0.20
5.1
0.375
9.5 9-8253
148
120
120
3.05
0.13
3.2
75
5.2 180 360
0.50 0.20
5.1
0.500
12.7 9-8253
152
120
75
1.91
0.15
3.8
75
5.2 180 360
0.70 0.20
5.1
0.625
15.9 9-8253
162
120
45
1.14
0.15
3.8
75
5.2 180 360
1.00 0.20
5.1
0.750
19.1 9-8253
163
120
35
0.89
0.15
3.8
75
5.2 180 360
NR NR
NR
1.000
25.4 9-8253
168
120
20
0.51
0.15
3.8
75
5.2 180 360
NR NR
NR
NOTE!
* Gas pressure shown is for torches with leads up to 25’ / 7.6 m long. For 50’ / 15.2 m leads, set gas pres-
sure to 70 psi / 4.8 bar.
** Total flow rate includes plasma and secondary gas flow.