EasyManuals Logo

Evinrude E-Tec 50 HP Service Manual

Evinrude E-Tec 50 HP
426 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #64 background imageLoading...
Page #64 background image
62
ENGINE MANAGEMENT MODULE (EMM)
S.A.F.E. WARNING SYSTEM
S.A.F.E. WARNING
SYSTEM
The S.A.F.E. (Speed Adjusting Failsafe Electron-
ics) warning system alert s t he oper ator and pro-
tects against engine d amage fro m t he fo llowing
abnormal conditions:
Activation
When one of these conditions occurs, the EMM
interrupts fuel injector and ignition o peration,
reducing engine speed to 1200 RPM. The warning
horn sounds and an Engine Monitor message dis-
plays. When S.A.F.E. is active, the engine will run
normally below 1200 RPM. Above 1200 RPM, the
engine will shake excessively.
Recovery
The engine will operate in S.A.F.E. as long as the
fault condition exists. To recover normal operation,
two conditions must be met:
Sensor or switch readings must be back with in
limits
The EMM must be reset—stop and restart
SHUTDOWN MODE
Outboard “sh utdown” will occur if specific fault s
are detected by the EMM:
Code 57 occurs when the EMM d etects abn or-
mally high RPM relative to the TPS positio n. This
condition could be cause d by u ncontrolled fue l
entering the co mbustion cycle. Before removing
the code and ST ARTING the outb oard, find and
repair the cause.
Perform Fuel System Pressure Test on p. 137.
Check for external fuel leakage that could allow
fuel and/o r vapo r to enter th e engine throug h
the air intake.
Check for internal fue l le akage from a le aking
injector or vapor separator vent hose.
Recovery
To recover from shu tdown mode , the EMM mus t
NOT detect the re lated fault at st art-up. The o ut-
board will not restart u ntil the cause of t he
occurred service co de is resolved (cod e 29 and
31) and the code is cleared using diagnostics soft-
ware (code 3 3 and 5 7). Then, the EMM must be
turned OFF and ON again.
IMPORTANT: Shutdown relate d to code 57 or
33 requires th e removal of th e occurred service
code. Use Evinrude Diagnostics software to clear
a code 57 or 33.
Code 17 Alternator 55 V below expected range
Code 18 Alternator 55 V above expected range
Code 25 EMM temperature above expected
range
Code 34 Oil injector open circuit
Code 40 Cylinder head temperature above
expected range–low speed
Code 43 Cylinder head temperature above
expected range–high speed
Code 117 NO OIL detected
Code 29 Excessive EMM temperature
Code 31 Excessive engine temperature
Code 33 Excessive NO OIL condition
Code 57 High RPM with low TPS setting
A WARNING
If the engine shuts OFF and the “CHECK
ENGINE” light or EMM SENSOR FAULT
LED is flashing, the engine cannot be
restarted. A hazardous fuel condition may
exist which could result in a fire or explo-
sion.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Evinrude E-Tec 50 HP and is the answer not in the manual?

Evinrude E-Tec 50 HP Specifications

General IconGeneral
Engine Type2-Stroke
Horsepower50 HP
Cylinders3
StartingElectric
SteeringRemote
Trim MethodPower Trim and Tilt
Shaft Length20 in. (508 mm)
Gear Ratio2.00:1
Oil InjectionYes
Displacement863 cc
Fuel InductionDirect Fuel Injection (DFI)

Related product manuals