Evinrude E-TEC G2 Operator's Guide

Evinrude E-TEC G2

84 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

© 2014 Bombardier Recreational Products Inc. All rights reserved. ®, TM and the BRP logo are trademarks of Bombardier Recreational Products or its affiliates

WARNING

Read this Guide thoroughly. It contains important safety information.

Minimum recommended operators age: 16 years old.

Keep this Operators Guide in the boat.

*216348*

200, 225, 250, 300 HORSEPOWER

Operator’s Guide

Revision D

Table of Contents

Table of Contents6
About this Guide8
Important Safety Messages9
- Product References, Illustrations and Specifications11
- Declaration of Conformity12
- Using Your Evinrude E-TEC G2 Outboard13
Important On-Product Labels14
Component Identification 200, 225, 250, 300 HP 74° V616
2-Stroke Engine Oil and Fuel18
- 2-Stroke Engine Oil Requirements18
- Oiling System Information18
- Fuel Requirements20
- Fuel System Information20
Operation23
- Safety Information23
- Engine Starting / Stopping23
- Engine Stopping25
- Remote Controls - Evinrude ICON II Control System27
- Remote Controls - Evinrude Mechanical Controls28
- Fuel Economy29
Trim, Tilt and Steering30
- Power Trim and Tilt30
- Impact Damage Protection32
- Dynamic Power Steering (DPS)33
Engine Monitoring34
- Displays and Gauges34
- Speed Adjusting Failsafe Electronics (S.A.F.E.)34
Special Operating Conditions36
- Cold and Freezing Weather36
- Multiple Outboard Operation36
- High Altitude36
- Salt Water36
- Shallow Water36
- Under Tow36
- Weedy Water36
Transporting the Outboard37
- Trailering37
- Transporting / Storage38
Pre-Ride Inspection39
Engine Emissions Installation Information42
Maintenance & Inspection Schedule44
- Engine Care Products44
Service45
- Anodes45
- Flushing45
- Fuses46
- Gearcase Lubricant Level46
- Hull Finish47
- Outboard External Finish47
- Scratch Repair47
- Spark Plugs47
- Submerged Outboard47
Storage48
- Short-Term Storage48
- Long-Term Storage (Winterization)48
Troubleshooting50
- S.A.F.E. Reset51
- Emergency Start Procedure52
- Product Information53
Installation54
- Transom Height54
- Outboard Shipping Cover54
- Installing the Outboard55
- Boat-Mounted Fuel Filters55
- Battery56
- Accessory Battery Connection57
- Water Pressure57
- Propeller58
- Adjustments59
Specifications60
- 200, 225, 250, 300 HP (3.4 Liter, 74° V6) Models60
Product Warranty Information63
- Warranty Information68
- California Emission Control Warranty Statement72
Readiness Test75
Frequently Asked Questions77
Change of Address / Change of Ownership79
Confirmation of Receipt81

Other manuals for Evinrude E-TEC G2

Questions and Answers:

Need help?

Do you have a question about the Evinrude E-TEC G2 and is the answer not in the manual?

Evinrude E-TEC G2 Specifications

General

Bore x Stroke	Varies by model
Full Throttle RPM Range	5400-6000 RPM
Alternator Output	133 Amps Total / 50 Net Dedicated
Lubrication	Multi-point targeted oiling
Cylinder Configuration	V6
Gear Ratio	1.85:1
Starting	Electric
Engine Type	2-stroke
Shaft Length	20", 25", 30"
Fuel Induction	Direct Fuel Injection (DFI)
Emissions	EPA 2013
Horsepower Range	150 - 300 HP
Fuel Type	87 Octane
Weight	505 - 635 lbs (varies by model)

Related product manuals

Preview: Evinrude E-Tec

Evinrude E-TEC 150

Preview: Evinrude E-TEC 200

Evinrude E-TEC 200

Evinrude E-TEC 300

Evinrude E-TEC 225

Evinrude E-TEC 250

Evinrude E-TEC 175

Evinrude E-TEC 130

Evinrude E-TEC 135

Preview: Evinrude E-TEC 90 H.O.

Evinrude E-TEC 90 H.O.

Preview: Evinrude E-TEC E40DRLSCB

Evinrude E-TEC E40DRLSCB

Evinrude E-TEC E50DPLSCB