FAAC E024S - MEMORY STORAGE OF RC;LC RADIO CONTROLS; RADIO CONTROLS DELETION PROCEDURE; BATTERY KIT OF E024 S (OPTIONAL)

E024S 12 732642 - Rev. F
a
10 MM
16 MM
16 MM
8.3.1 REMOTE MEMORY STORAGE OF RC/LC RADIO
CONTROLS
OtherradiocontrolscanberemotelystoredonlywiththeRC/LC
radiocontrols,i.e.withoutusingtheLOGIC-SPEED-SETUPpush-
buttons,butusingapreviouslystoredradiocontrol.
1. Getaradiocontrolalreadystoredononeofthe2channels
(OPENAorOPENB).
2. Pressandholddownpush-buttonsP1andP2simultaneously
untilboththeLEDsflashslowlyfor5sec.
3. Within5sec.pressthepush-buttonoftheradiocontrolthathad
beenmemorystoredtoenablelearningontheselected
channel.
system is free of any obstacle created by
persons or things.
To add other radio controls, transfer the code of the
memory-storedpush-buttonoftheradiocontroltotherelevant
push-buttonoftheradiocontrolstobeadded,observingthe
followingprocedure.
• Onthememorystoredradiocontrol,simultaneouslypress
andholddownpush-buttonsP1andP2.
• TheradiocontrolLEDbeginstoflash.
• Releasebothpush-buttons.
• Pressthememorystoredpush-buttonandholditdown
(theradiocontrolLEDlightsuponsteadybeam).
• Bringtheradiocontrolsnear,pressandholddownthe
push-buttonoftheradiocontroltobeadded,releasing
it only after the double flash of the radio control LED,
whichindicatesmemorystorageexecuted.
• Quicklypresstwicethepush-buttonofthememorystored
radiocontrol.
The automated system performs one opening
operation. Make sure that the automated
system is free of any obstacle created by
persons or things.
8.3 MEMORY STORAGE OF RC/LC RADIO CONTROLS
A maximum of 250 codes can be memory
stored, split between OPEN A and OPEN B.
1. UseRC/LCremotecontrolsonlywithreceivermoduleat433
MHz.
2. PresstheLOGIC(SW3)orSPEED(SW2)push-button,tomemory
storerespectivelytotalopening(OPENA)orpartialopening
(OPENB),andasyouholditdown,alsopresstheSETUP(SW1)
push-button.TherelevantLEDstartstoflashslowlyfor5sec.
3. Releasebothpush-buttons.Withinthese5sec.,pressthe
appropriatepush-buttonontheRCorLCremotecontrol.
4. TheLEDlightsuponsteadybeamfor1second,indicating
memorystorageexecuted,andthenresumesflashingfor
another5sec.,duringwhichanotherradiocontrol(point
4)canbememorystored.
5. Whenthe5sec.haveelapsed,theLEDgoesOFFindicating
theendoftheprocedure.
6. Toaddotherradiocontrols,repeattheoperationatpoint1.
4. TheLEDontheboardrelatingtothechannelbeinglearned
flashesfor5sec.,withinwhichtimethecodeofanother
radiocontrolmustbetransmitted.
5. TheLEDlightsuponsteadybeamfor2seconds,indicating
memorystorageexecuted,andthenresumesflashingfor
5sec.,duringwhichotherradiocontrolscanbememory
stored,andthengoesOFF.
8.4 RADIO CONTROLS DELETION PROCEDURE
1. TodeleteALLtheinputradiocontrolcodes,presspush-button
LOGIC(SW3)orSPEED(SW2)and,whileholdingitdown,also
presspush-buttonSETUP(SW1)for10sec.
2. TheLEDrelatingtothepressedpush-buttonflashesforthefirst
5sec,andthenflashesmorequicklyforthenext5sec.
3. BothLEDslightuponsteadybeamfor2secandthengoOFF
(deletion completed).
4. Releasebothpush-buttons.
This operation is NOT reversible. All codes of
radio controls stored as OPEN A and OPEN B will
be deleted.
9 BATTERY KIT OF E024S (OPTIONAL)
Thebufferbatterykitwasbuiltfor insertion inside the control
boardsupport.
This support (Fig.4 ref.a) was pre-moulded to permit the
batteryhousingtobeopened.
1. Remove the board support material covering the
batteryhousing,cuttingthematerialconnectionsalong
theperimeter.
2. Insertthebatteryinthehousingyouhavejustcreated,and
secureitontheanchoringsupports(Fig.5).
3. TocorrectlyfastenandconnectthecontrolunittotheJ11con-
nector,refertotheinstructionsenclosedwiththebatterykit.
Fig.4
Fig.5
ENGLISH