Fagor Compact Drives and Motors Quick Reference. Ref.1910 CQR-15/56
DIMENSIONS
CONNECTORS
Motor power connector
Motor feedback connector
HOLDING BRAKE CHARACTERISTICS
Optional on all models. The holding brake (motor shaft) must never
exceed its maximum speed. Voltage over 22-26 V DC will lock the
axis.
FAN CHARACTERISTICS
FKM1 motors do not offer the fan in any of their models.
GENERAL MOUNTING CONDITIONS
Before installing in onto the machine, the anti-rust paint should be
removed from the rotor shaft and the flange. It must always be in a
dry and clean place. Mounted so it is easily inspected, cleaned and
maintained.
Free of corrosive atmosphere and/or explosive gasses or liquids. If
the motor is going to be continously exposed to oil splashes, it should
be protected with a guard.
CAUTION !
When installing pulleys or gears for transmission, avoid
hitting the shaft. Use some tool that is supported in the
threaded hole on the shaft to insert the pulley or the gear.
AXIAL | RADIAL LOADS
A poor alignment between the motor shaft and the machine axis
increases vibration of the shaft and reduces the useful life of bearings
and couplings.
Likewise, exceeding certain maximum radial load values on the
bearings has a similar effect.
Follow these considerations in order to avoid these problems:
Use flexible couplings for direct coupling.
Avoid radial and axial loads on the motor shaft making sure not to
exceed the limit values.
MOUNTING ARRANGEMENTS ·IM CODE·
IDENTIFICATION
Names
The denomination of each motor is made up of letters and digits that
mean the following. The sales model is stored in the motor encoder.
The drive software can automatically adjust the motor parameters by
reading that ·sales model· from the encoder memory.
Motor model nomenclature
Motor Holding
torque
Power
consumption
Time
on/off
Inertia Approx.
mass
Units N·m lbf·ft W hp ms kg·cm²
kg
lb
FKM1
2.0 1.47 11 0.014 6/25 0.068 0.15 0.33
Note. The maximum turning speed of the holding brake for the FKM1
series is 10000 rev/min.
CABLE LENGTH 1.0 m
43
Ø
7
4
50.6
25
Ø
6
3
3
50
K
20
6
2.5
Ø40j6
143
Ø9k6
M3
8
55
4x R2.9
56.5
DIMENSION
k
MOTOR BRAKELESS WITH BRAKE
Units mm in mm in
FKM12 109 4.29 147 5.78
FKM14 139 5.47 177 6.96
FKM1
DIMENSIONS in mm
1 in = 25.4 mm
97 (3.82)
80 (3.15)
27 (1.06)
MC-20/6
1000 (39.36)
approx.
MPC-4x1.5
MC-20/6
SEALING: IP 65
PIN
SIGNAL
1
2
6
3
4
5
U PHASE
V PHASE
W PHASE
PE
-
-
(1)
OUTSIDE VIEW OF THE MOTOR
POWER CONNECTOR
11
12
THERMISTOR
THERMISTOR
EOC-12
SEALING: IP65 STAND
PIN
SIGNAL
1
2
3
4
5
6
REFCOS
+485
PTC111
PTC111
SIN
REFSIN
PIN
SIGNAL
7
8
9
10
-485
COS
CHASSIS
GND
NOT CONNECTED
+8 V DC
(2)
OUTSIDE VIEW OF THE
MOTOR FEEDBACK
CONNECTOR
EEC-SP-X
SINUSOIDAL ENCODER, REFs. A4/E4
EOC-12
(2)
MANDATORY. When applying a combined axis and radial
load, decrease the maximum radial force allowed ·Fr· to
70% of the value indicated in the table.
Series Axial force
·Fax·
Radial force
·Fr·
Distance
·d·
Units N lbf N lbf mm in
· without holding brake ·
FKM1
45 10.11 234 52.60 8.75 0.34
FKM1
48 10.79 254 57.10 8.75 0.34
· with holding brake ·
FKM1
48 10.79 254 57.10 8.75 0.34
FKM1
50 11.24 264 59.34 8.75 0.34
IM B5
IM V3
IM V1
IEC 60034-7, code I
To Next Page
Loading...
