Fanimation BLITZ LP8377LBN User Manual

Fanimation BLITZ LP8377LBN

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.

Date Code

Purchase Date

ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM

READ AND SAVE THESE INSTRUCTIONS

For best and quick service please provide date code. You can find the date code on the Carton,

Handheld Remote (inside of the battery compartment), Receiver or top of Fan Housing.

Net Weight 16.12 lbs (7.31 kgs)

BLITZ CEILING FAN

MODEL #

LP8377LBN

ITEM #2483971

Español p. 21

™

Table of Contents

Questions and Answers:

S
shahlindaAug 6, 2025
What to do if my Fanimation Fan will not start?
- T
  tbaileyAug 6, 2025
  If your Fanimation Fan won't start, there are several things to check: 1. Make sure that the fuse or circuit breaker hasn't blown. Check both the main and branch circuit fuses or circuit breakers. 2. Inspect the power line connections to the fan and the switch wire connections in the switch housings. Ensure they are secure. Remember to turn off the main power before checking! 3. If you're using a remote control, the battery might be dead. Try replacing it with a new one. 4. The reverse switch might be in a neutral position. Ensure it's fully to one side.
S
samuel05Aug 16, 2025
Why is my Fanimation Fan so noisy?
- K
  Kevin MillerAug 16, 2025
  If your Fanimation Fan is making excessive noise, here's what you can do: 1. Ensure the blades are properly attached to the fan. 2. Check all screws in the motor housing to make sure they are snug (but not over-tightened). 3. Examine the wire connectors inside the switch housing to ensure they are not rattling against each other or the housing's interior wall. Be sure to turn off the main power before checking! 4. The noise might be due to a solid-state variable speed control. These controls are not recommended, so consider an alternative control method.
R
Rachel HallAug 27, 2025
How to fix a Fanimation BLITZ LP8377LBN that wobbles a lot?
- C
  Curtis GilbertAug 27, 2025
  If your Fanimation Fan wobbles excessively, check the following: 1. Tighten both setscrews and nuts securely in the downrod support. 2. Ensure the setscrew in the downrod/hanger ball assembly is tightened. 3. Verify that the screws securing the fan blade to the motor hub are tight. 4. Make sure the hanger bracket screws are tightened to the outlet box, and that the outlet box itself is secure.

Fanimation BLITZ LP8377LBN Specifications

General

Model	BLITZ LP8377LBN
Category	Fan
Type	Ceiling Fan
Finish	Brushed Nickel
Blade Span	52 inches
Number of Blades	5
Blade Pitch	12 degrees
Control	Remote Control
Speeds	3
Light Kit Included	Yes
Light Type	LED
Dimmable	Yes
Location	Indoor
Reversible	Yes
Mounting	Downrod
Warranty	Limited Lifetime
Motor Type	AC Motor
Blade Material	ABS

Summary

Important Safety Instructions

Additional Safety Instructions

Limited Lifetime Warranty

Unpacking Instructions

Check Parts Received

Verify all fan components are present before proceeding with installation.

Energy Efficient Use of Ceiling Fans

Choosing the Appropriate Mounting Location

Install fan centrally, 7ft from floor, 18in from wall for optimal airflow.

Turn Off When Not in the Room

Switch off the fan when the room is unoccupied to save energy.

Using the Ceiling Fan Year Round

Use counterclockwise for summer cooling, clockwise for winter heating.

Electrical and Structural Requirements

How to Assemble Your Ceiling Fan

Prepare Downrod and Motor

Remove hanger ball, clevis pin, hairpin clip, stabilizer tabs; route wires.

Route Wires and Assemble Canopy

Route wires through covers and canopy, re-hang hanger ball securely.

Prepare Wires and Hanger Bracket

Cut excess wire, strip ends, remove one shoulder screw from hanger bracket.

How to Hang Your Ceiling Fan

Secure Hanger Bracket

Attach hanger bracket securely to the outlet box using outlet box screws.

Seat Downrod/Hanger Ball

Lift fan, seat downrod/hanger ball assembly onto hanger bracket, align tab in groove.

How to Wire Your Ceiling Fan

Set Remote Receiver Code

Slide dip switches on receiver to match code set on remote control.

Install Receiver in Hanger Bracket

Slide the receiver unit into the hanger bracket before making wire connections.

Connect Receiver Wires

Connect receiver wires to fan and supply wires using wire connectors.

Secure Wire Connections

Ensure all connections are tight, no bare wire visible, except ground wire.

How to Install Your Canopy Housing

Assemble Canopy

Rotate canopy onto shoulder screws in hanger bracket, tighten screws.

Attach Canopy Screw Cover

Secure canopy screw cover over shoulder screws using twist-lock feature.

How to Assemble Your Ceiling Fan Blades

Attach Blades to Motor Hub

Slide blade through slot and secure with serrated head screws and flat washers.

How to Assemble Your Light Kit Assembly or Cap

Assemble Light Kit to Bracket

Attach light kit to support bracket using key slots and screws.

Install Light Kit Wire Cover

Attach wire cover to light kit using key slots and screws.

Connect LED Assembly

Connect 2-pin connectors from LED assembly to motor assembly.

Install Steel Cap

Twist steel cap onto light kit clockwise to secure.

Assemble LED Assembly

Assemble LED assembly to light kit using key slots and screws.

Secure Glass to Light Kit

Twist glass clockwise onto light kit until it snaps into place.

How to Operate Your Ceiling Fan

Important Operation Notes

Do not use dimmer switches; restore power after checking connections.

Install Remote Batteries

Install two 3V batteries in the remote transmitter.

Set Remote Control Code

Slide dip switches on remote to match receiver code for operation.

Remote Functions Overview

Explains fan speed, light control, sleep timer, and special features.

Advanced Fan Operations

Details fresh air mode, safe exit feature, and reverse button operation.

How to Install Your Remote Control

Install Wall Holder

Attach the wall plate for the remote control using two provided screws.

Maintenance and Cleaning

Troubleshooting

Parts List

Exploded-View Illustration

Related product manuals

Preview: Fanimation BECKWITH FP7964BOB

Fanimation BECKWITH FP7964BOB

Preview: Beckwith FP7964B Series

Beckwith FP7964B Series

Preview: Fanimation Subtle

Fanimation Subtle

Preview: Fanimation SPITFIRE

Fanimation SPITFIRE

Fanimation Wet Location

Preview: Fanimation FP6729 series

Fanimation FP6729 series

Preview: Fanimation The Torto FP7900

Fanimation The Torto FP7900

Preview: Fanimation XENO FP6729B Series

Fanimation XENO FP6729B Series

Preview: Fanimation Upright LP8577 Series

Fanimation Upright LP8577 Series

Preview: Escalade FP2320 Series

Escalade FP2320 Series

Preview: Involution FP4520 Series

Involution FP4520 Series

Preview: SCULPTAIRE FP8511 Series

SCULPTAIRE FP8511 Series